F8-1. Determine the vertical displacement of joint B. AE is constant. Use the principle of virtual work. F8-2. Solve Prob. F8-1 using Castigliano's theorem. 600 N 3 m 4 m B Probs, F8-1/2

Q: Determine the magnitude of the pin reactions at B and Cif W = 2180 Ib. 3.5' 3.5' B 2.1' W D

A: let VB is reaction at B and HC is reaction at C in horizontal direction, and HD and VD are reaction…

Q: Hinge supports exist at points D and E. Internal pin connections exist at points B and G. Point F is…

A: The free-body diagram of BC having vertical and horizontal reactions at B and vertical reaction at…

Q: 9-15. Determine the vertical displacement of joint A. Assume the members are pin connected at their…

A:

Q: 4-9. The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm…

A:

Q: 4-41. Compute the torsional shear stress that would be produced in a solid circular shaft having a…

A:

Q: 4-35 Deter mine compressive logds in members AB and BC. FBD of B BC AB=160 AB/I5 160lb AB = 3401bin…

A:

Q: 2-1. The steel framework is used to support the reinforced stone concrete slab that is used for an…

A:

Q: *4-4. The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod…

A:

Q: Determine the magnitude of the pin force at A.

A:

Q: Determine the magnitude of the pin force at A. Assume W = 510 lb, a = 3.0 ft, b = 2.0 ft, r = 6 in.…

A:

Q: F8-9. Determine the vertical displacement of joint B. AE is constant. Use the principle of virtual…

A:

Q: The bracket is held to the wall using three A-36 steel bolts at B, C, and D Each bolt has a diameter…

A: To findif a force P = 450 lb is placed on the bracket as shown, determine how far s, the top bracket…

Q: A 200-mm lever AB and a 240-mm-diameter pulley are welded to the axle BE, which is supported by…

A:

Q: 5-51. If a clamping force of 300 N is required at A, determine the amount of forceF that must be…

A: Consider the segment A, C and D of the system and draw the free body diagram of the segment.

Q: 3. Determine the horizontal AND vertical displacements of joint B using energy method. All members…

A:

Q: F8-7. Determine the vertical displacement of joint D. AE is constant. Use the principle of virtual…

A: Given that : Put the values in the table                   MembersLengthP ( kN )AB3 m   ?BC3 m…

Q: If P = 4.1 kN , determine the horizontal displacement of end F of rod EF.

A:

Q: 16-6. Determine the support reactions at pins and 3. Take E = 200 GPa, I = 350(10) mm, A = 15(10³)…

A: Determine the support reactions at pins 1 and 2. Take E 200 GPa, I = 350(106 ) mm4 , A = 15(103 )…

Q: 4-12 Deterinizne tihe ruient of the 750-N force shown in. Pig. P412 albout points A, 3, and C. F=…

A: Given Data: The magnitude of the force is F = 750 N. The angle of force with horizontal is θ=25∘.…

Q: Use the method of sections to solve for the following members in the Truss shown below: EF, FC, BC

A: Given  figure To solve for the member : EF, FC, BC

Q: 5-15. Determine the reaction at fixed support A. Problem 5-15 3 kN 0.5 kN/m SKN- m The left end of…

A: For the given beam  To determine  Reactions at A

Q: 6-65 Determine the horizontal and vertical components of force that pins A and B exert on the frame.…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.