F16-6. For a short period of time, the motor turns gear Awith a constant angular acceleration of a = 4.5 rad/s²,starting from rest. Determine the velocity of the cylinder andthe distance it travels in three seconds. The cord is wrappedaround pulley D which is rigidly attached to gear B.225 mm75 mm125 mma = 4.5 rad/s AdC.

The tangential acceleration for both gears A and B will be the same so,

Answered: F16-6. For a short period of time, the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cord, which is wrapped around the disk, is given an acceleration of a=(12t)m/s2, where t is in seconds A) Starting from rest, determine the angular displacement of the disk, measured clockwise, when t = 3 s B) Starting from rest, determine the angular velocity of the disk, measured clockwise, when t = 3 s C) Starting from rest, determine the angular acceleration of the disk, measured clockwise, when t = 3 s .
υο VA W= A r v B CC A gear sits between two moving racks. If the top rack moves at a velocity of v₁ = 0.85 m/s to the left and the bottom rack moves at a velocity of VB = 0.3 m/s to the right, determine the velocity at the center of the gear, the magnitude of the angular velocity of the gear, and the distance to the ICZV from point B. The gear has a radius of r = 0.08 m. m/s Select an answer rad/s Select an answer VB BY UBC Engineering
= At the instant shown rod AB has an angular velocity WAB 4 rad/s and an angular acceleration AB 2 rad/s2. Determine the angular velocity and angular acceleration of rod CD at this instant. The collar at C is pin connected to CD and slides freely along AB. = a) using the relative motion analysis and the contact conditions. A 4 rad/s AB= 2 rad/s² WAB 60° 0 = 0.75 m -0.5 m В B D
a - 12 rad/s 16-3. B The disk is originally rotating at e, = 12 rad/s If it is subjected to a constant angular acceleration of a = 20 rad/s, determine the magnitudes of the velocity and the n and f components of acceleration of point A at the instant t = 2s 04 m 0.5 m-A
The slotted arm AB drives pin "C" through the spiral groove described by the equation r = = (30) ft, where "0" is in radians. If the arm starts from rest when 0 = 60° and is driven at an angular velocity of 8 = (4t) rad/s, where "t" is in seconds, determine the radial and transverse components of velocity and acceleration of the pin "C" when t = 1 s. B C Ans. a₁ = -134.3 ft/s² Ans. ā= 132.6 ft/s²
A motor gives gear A an angular acceleration of αA=0.006θ^2 rad/s2, where θ is in radians. If this gear is initially turning at ωA=10 rad/s, Determine the angular displacement of gear A at the instant at which gear A reaches angular velocity of 35 rad/s. Determine the angular velocity and acceleration of gear B at this instant. Find the magnitude of acceleration of point P on the pitch circle of gear B at this instant.
At a given instant the top BB of the ladder has an acceleration aBaBa_B = 2.1 ft/s2ft/s2 and a velocity of vBvBv_B = 4.0 ft/sft/s , both acting downward Determine the acceleration of the bottom AA of the ladder. Determine the ladder's angular acceleration at this instant.
The hydraulic cylinder gives pin A a constant velocity v = 2.0 m/s along its axis for an interval of motion and, in turn, causes the slotted arm to rotate about O. Determine the values of r, r, and 0 for the instant when 0 = 32°. (Hint: Recognize that all acceleration components are zero when the velocity is constant.) Answers: r = 7 = 0 = A i i i 0 34 260 mm- m/s m/s² rad/s²
The disk rotates about the shaft SS, while the shaft is turning about the zz axis at a rate of ωzωzomega_z = 6 rad/srad/s , which is increasing at ααalpha = 2.5 rad/s2rad/s2 . No slipping occurs. Determine the xx, yy, and zz components of the velocity of point BB on the disk at the instant shown using scalar notation. Determine the xx, yy, and zz components of the acceleration of point BB on the disk at the instant shown using scalar notation.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS