F14-11. If the 50-kg load A is hoisted by motor M so that theload has a constant velocity of 1.5 m/s, determine the powerinput to the motor, which operates at an efficiency e = 0.8.1.5 m/s

Answered: Image /qna-images/answer/c0e09a26-9399-4fba-b1aa-af0f392c99a3.jpg

Answered: F14-11. If the 50-kg load A is hoisted…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4 m M = (301²) N.m F = 15t N If the rod of negligible mass is subjected to a couple moment of M=24t² N;M where t is the time in seconds, and the engine of the car supplies a braking force F= 15t N to the wheels, determine the speed of the car at t= 10s. The car at t=0s a a speed of 9 m/s. The total mass of the car and the driver is 135 kg. Neglect the size of the car.
The 5 lb weigh shone has a velocity of 10 ft/s when it is 3 ft above the spring platform Cables hold the spring at a length of 1 ft.. Ignore the weight of the cables and the platform. The uncompressed length of the spring is 1.75 ft. Determine the maximum additional compression of the spring. 5 lb 10 ft/s 3 ft x, = 0.75 ft. k = 400 lb/ft
15-51. The 30-Mg freight car A and 15-Mg freight car B are moving towards each other with the velocities shown. Determine the maximum compression of the spring mounted on car A. Neglect rolling resistance
The small 0.20-kg slider is known to move from position A to position B along the vertical-plane slot. Determine (a) the work done on the body by its weight and (b) the work done on the body by the spring. The distance R = 1.15 m, the spring modulus k = 155 N/m, and the unstretched length of the spring is 0.85 m. B Answers: R 4 R k A (a) Work done on the body by its weight: Ug = (b) Work done on the body by the spring: Us= i i N•m N.m
The belt tension in the tight and slack sections is 25 N and 15 N, respectively. The belt operates at a speed of 10 m/s. How much power is delivered by the transmission system?
14-59. The escalator steps move with a constant speed of 0.6 m/s. If the steps are 125 mm high and 250 mm in length, determine the power of a motor needed to lift an average mass of 150 kg per step. There are 32 steps. *14-60. If the escalator in Prob. 14–46 is not moving, determine the constant speed at which a man having a mass of 80 kg must walk up the steps to generate 100 W of power-the same amount that is needed to power a standard light bulb. 250 mm - 125 mm v = 0.6 m/s 4 m
The 2-Mg car increases its speed uniformly from rest to 20 m/s in 30 s up the inclined road. Determine the maximum power that must be supplied by the engine, which operates with an efficiency of E= 0,4. 10
A tugboat T having a mass of 19 Mg is tied to a barge B having a mass of 75 Mg. If the rope is "elastic" such that it has a stiffness of k=600kN/m, determine the maximum stretch in the rope during the initial towing. Originally both the tugboat and barge are moving in the same direction with speeds (vT)1= 15 km/h and (vB)1= 10 km/h, respectively. Neglect the resistance of the water.
14-51. The 1000-lb elevator is hoisted by the pulley system and motor M. If the motor exerts a constant force of 500 lb on the cable, determine the power that must be supplied to the motor at the instant the load has been hoisted s = 15 ft starting from rest. The motor has an efficiency of ɛ = 0.65. %3D м Токожеже!
Determine the kinetic energy of the system. Assume that neither cable slips on the pulley.
The 1.5 Mg car increases its speed uniformly from rest to 36 m/s in 8 s up the inclined road. Determine the maximum power that must be supplied by the engine, which operates with an efficiency of ε = 0.42. Also, find the average power supplied by the engine. Please show every single step of the process thanks
The 10 kg block is subject to the action of a force that has the constant direction towards the spring, with a magnitude F= 250 (1 + x) N, where x is measured in meters. If the coefficient of kinetic friction between the block and the horizontal surface is 0.20, and ks= 50 N/m Use the springs por your calculations Determine: a) The work done by all the forces acting on the block during a movement from A to B. b) If the block starts from rest at point A, determine its velocity at point B using the equation of motion (Newton's 2nd Law). c) Verify the speed obtained in b) through the equation of work and Kinetic Energy. d) Explain the differences between the two methods used to find the velocity, from the point of view of the volume of calculations. Recomendations: 1. No force (except weight) is constant throughout travel 2. Acceleration is not constant at any point along the way. 3. When applying Newton's second law, it is advisable to do it in two sections. 4. Review the…

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

F14-11. If the 50-kg load A is hoisted by motor M so that the load has a constant velocity of 1.5 m/s, determine the power input to the motor, which operates at an efficiency e = 0.8. 1.5 m/s