F1 = 10N, F2 = 15N, F3 = 8N, F4 = 10N, F5 = 18N, and the length of the side of a red square is 1m… Calculate the direction of the resultant force (in degrees). Express your answers in 2 decimal places. Do not include the orientation (N of E, S of W, etc.) of the direction.

Q: INTERNAL FORCES - EQUATION i) What is the equation for shear force V(x) and bending moment M(x EACH…

A: …

Q: The force F is resolved into two component on u and v axes. If force F is to have a component along…

A:

Q: W d OD g FA FB NOTE: angles c, d, f, g, are not drawn to scale X

A: Given FA = 185 lb FB = 189 lb Angles C = 7° D = 21° F = 9° G = 11°

Q: A W C L/2- Use the following values for the problem: w = 143 kN/m L = 5.4 m E = 60 GPa I= 256 x 10^6…

A:

Q: he beam shown carries a uniformly distributed load from B to D and a 2700 N-m moment at D. Derive…

A: Shear force is normally a force acting in a particular direction that is parallel to a cross-section…

Q: Calculate the moment of inertia of the cross section of the beam about its centroidal xo-axis.…

A:

Q: Determine the shear force and moment acting at point C of the beam shown in (Figure 1). For the…

A:

Q: own in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that LAB = 2100…

A: Given data LAB =2100 mm, LBC =2900 mm, B0= 20mm B 1 = 30mm   H = 240mm h0= 160mm h1 = 40mm

Q: 9. MEASURED CLOCKWISE FROM THE POSITIVE X-AXIS, DETERMINE THE DIRECTION AND THE MAGNITUDE OF THE…

A: Given:- Three forces are given, The magnitude of the first force (F1) = 850 N The magnitude of the…

Q: Determine the force (P) required to keep the block to move up, given that μs = 0.33 and μk = 0.21.…

A:

Q: Part A Determine the distance ī to the centroid of the beam's cross-sectional area. Set a = 70 mm ,…

A:

Q: Determine the shear force and moment acting at point C of the beam shown in (Figure 1). For the…

A: Given data:-

Q: Problem Number 6. A simply supported beam has a length of 4m. The beam is carrying a 500N downward…

A: L = 4m

Q: The two (x = 20-ft) beams shown in Figure are to be moved horizontally with respect to each other…

A:

Q: 4. A certain area has the following properties: lx = 28 in4; ly = 66 in4; Pxy = 36 in4, determine…

A:

Q: The resultant of the two forces F = 1023 N and P = 1412 N is a vertical force directed upward. If…

A: Given data, F = 1023 N P = 1412 N Resultant acting perpendicular with horizontal axis.

Q: F2 -300 N F=700 N 60 M. =1500 Nm 2 m 3m or the above diagram, given that F, = 450 N, 8 = 30 degrees…

A:

Q: Draw the shear force and bending moment diagram of the beam. Draw the distribution of normal stress…

A: To draw the Shear and Normal Stress distribution for T section.q=12t/m, b=85mm, h= 750mm, t=30mm B =…

Q: Two cantilever beams are arranged as shown in the figure. They have rectangular cross sections…

A:

Q: Find the vertical deflection at point L2 and horizontal deflection at point L4. The circle figures…

A:

Q: ..A force is specified by the vector F = 1201 + 160j +80k lb. Calculate the angles made by F with…

A:

Q: Three cables A, B and C are attached to the hook. The magnitude of A, and the magnitude & angle of C…

A:

Q: D 10 in. A B| y

A:

Q: M 12 m. 60° Sin. 40 lb Problem 03.114.b - Location of the resultant force Locate the points where…

A:

Q: 4. If the 3 forces are NOT in equilibrium, and P = 200 N, what is the horizontal component of the…

A: Given,  X = 137 Y = 37   As requested, we are required to solve the questions 4,5 and 6.

Q: In the system shown, determine the value of the force F if the coefficient of friction between the…

A:

Q: Using an algebraic summation of components, calculate the resultant R of forces A, B and C. Find…

A: Horizontal component :Rx=-200442+32+170882+152Rx=-80NVertical component…

Q: Calculate the value of the deflection at point C. Enter your answer in mm to three decimal places.…

A: Given:Required:Deflection at C

Q: Calculate the moment of inertia of the cross section of the beam about its centroidal xo-axis.…

A:

Q: PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you…

A:

Q: 16. Determine the vertical deviation of the right support relative to the tangent 4 drawn at the…

A: Determination of Vertical deviation of the right Support relative to the tangent drawn at the left…

Q: please fill in all the blanks and show all work, thank you! 2%/ft Ay Find the reactions. Draw and…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: . Find the deflection of the be

A:

Q: X Y A b H G FbE А a Bb Cb D

A:

Q: Determine the shear force and moment acting at point C of the beam shown in (Figure 1). For the…

A:

Q: Required information Consider the beam given in the figure. Given: X = 0.4 in, E = 30,000 kips/in²,…

A: E = 30,000 kip/in.2I = 240 in.4Determine the support reaction and draw the shear force and bending…

Q: Determine the magnitude(lb) of the vertical component of force at point C if P = 137 lb, x = 14.7…

A:

Q: Apply equilibrium conditions in the horizontal and vertical planes: EF, = 0 N-Ncos 30° +0.3N cos 60°…

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.