F, a triangular distributed load and couple moments M1., M6 are applied a rigid frame 1..... structure which has a fixed support at A. Distributed load is in the negative z direction and couple moments are parallel to one of the x, y or z axis. All members of the frame structure are rigidly connected and parallel to one of the x, y or z axis. Find the support reactions. (Neglect the dimensions of the frame members) M, K E M6 B d H M, a M5 b F b d M1 (Nm) M4 (Nm) (Nm) (Nm) M2 M3 M5 M6 a. e (N) (Nm) (Nm) | N/m) (deg) (deg) (deg) (m) (m) (m) (т) (m) 100 100 150 200 50 50 60 70 2 2 3 2 3

F, a triangular distributed load and couple moments M1., M6 are applied a rigid frame 1..... structure which has a fixed support at A. Distributed load is in the negative z direction and couple moments are parallel to one of the x, y or z axis. All members of the frame structure are rigidly connected and parallel to one of the x, y or z axis. Find the support reactions. (Neglect the dimensions of the frame members) M, K E M6 B d H M, a M5 b F b d M1 (Nm) M4 (Nm) (Nm) (Nm) M2 M3 M5 M6 a. e (N) (Nm) (Nm) | N/m) (deg) (deg) (deg) (m) (m) (m) (т) (m) 100 100 150 200 50 50 60 70 2 2 3 2 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the forces in members CG and GH of the symmetrically loaded truss. The forces are positive if in tension and negative if in compression. B 5 m A Answers: CG= i GH = i -5 m 30° 5 m H L -6 m G D L -5 m L ΦΕ
All members in the rigid-jointed frame shown are prismatic and have the same flexural stiffness El. Find the magnitude of the bending moment at Q y (in kNm) due to the given loading 4m |S 2m IT R 100 kNm 2m Q P.
Situation 1. Determine the reactions in the fixed end supports assuming El is constant. Use the integration method to determine the end moments. 2m 900 N/m 4m 3m FINAL ANSWER
3) A plane truss is shown in the figure. 3-a) Determine the support reactions. 3-b) Find the forces in the members 1, 2, 3, 4, and 5. a = 2 m b=1m P = 10 KN b V a H U a D P a Q = 4 kN| U (4 B a E 5
Problem 6 For the following truss structure, compute: 1. All support reactions 2. Determine any zero-force members, if exist. 3. Determine the forces in all bars. Hint: Find the angle BCD. Then find the distance of C from the ground. 300 lb 300 lb A 13 ft 45° B 5 ft 12 ft D 13 ft 12 ft
The planar structurc RST snown in the figure is roller supported at S and pn supported at R. Mombers RS and ST has uniform flexural rigidiry (El) and S is a rigid joint. Consider only bending deformation and neglect cffects of solf woight and ax al stiffening. L 2 R When the structure is subjected to a concentrated horizontal load P at the end I. the magnitude of rotat on at the support R. is
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 1L 60° Answers: Ay = i Dy= Dx= i i B 3L 60° 60° E y 1 1L L L L 30° x 4L D
The bent rod is supported at A,B, and C by smooth journal bearings. Determine the components of reaction at the bearings if the rod is subjected to the force F=800N. The bearings are in proper alignment and exert only force reactions on the rod.
For the truss shown in the figure, determine the reactions and bar forces assuming the C, as a redundant. AE is constant for all members. A
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 2L A 60° Answers: Ay = i Dy= Dx= i i B 1L 1 C 1L 60° 60° E L L L 30° x 2L D
The frame shown supports a load W DE 1000 lb through the cable that passes through 3 pulleys and at the end is attached to a frame, also supports the distributed loads ω1 = 100 lb / ft; ω2 = 60 lb / ft and ω3 = 50 lb / ft. Determine: 1. Reactions at supports A and E. 2. Forces acting on bar ABCDE, show the results in graphical form of the beam. That is, you must make the simplified free-body diagram of the loads that act only on the horizontal element. 3. Make the shear force and bending-moment diagrams for the entire beam. The geometry and load data are as follows: see the geometry and load in the images. Clarification: THE CABLE GOES BEHIND THE FRAME AND THE CONTACT IS ONLY WITH THE PULLEYS AND THE GRIP TO THE FRAME (WALL).All pulleys have the same radius.
Find the force in each member of the truss by using: The method of consistent deformations. Take the member AB as a redundant. The stiffness EA is constant. 1.2 m 0.9 m B 10 kN 0.9 m ALIA