External Problem 2: Linear Momentum and Bernoulli Equations The double nozzle in the figure below discharges water at A and B into the atmosphere at a rate of 0.5 m³/s. The nozzle is lying in a horizontal plane. Assume steady and frictionless flow and the water speed in each jet (A and B) to be the same. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe inlet is 30 cm in diameter. (p = 1000 kg/m³). a) Applying Bernoulli's equation between the inlet section and any of the outlet sections, show that the pressure at section 1 is 315 612 Pa gage; b) What force acting through the flange bolt is required to hold the nozzle in place?

External Problem 2: Linear Momentum and Bernoulli Equations The double nozzle in the figure below discharges water at A and B into the atmosphere at a rate of 0.5 m³/s. The nozzle is lying in a horizontal plane. Assume steady and frictionless flow and the water speed in each jet (A and B) to be the same. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe inlet is 30 cm in diameter. (p = 1000 kg/m³). a) Applying Bernoulli's equation between the inlet section and any of the outlet sections, show that the pressure at section 1 is 315 612 Pa gage; b) What force acting through the flange bolt is required to hold the nozzle in place?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single-stage axial flow pump with outer radius r2 = 0.240 m and inner radius r1=0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q = 0.265 m^3/s, a water density p = 1.000 x 103 kg/m^3, a rotation speed n = 2.4 x 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2, and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Looking at the following image, find all values of the velocity triangle just before the impeller inlet and just after the impeller outlet at radius r =0.09 m. impeller Figure 37.1 A propeller of an axial flow pump a₁ w1 U₁ Outlet guide vane B₁ Impeller α₂ Vw2 U₂=U₂=U
Turbo machines
In a centrifugal blower (Figure Q1) air enters in to the blower normal to the blades (a1 = 0°), and exits at 40°from the radial direction (∞2=40°). The blower rotates at w = 200 rad/s. The inlet radius r1 = 4 cm, and inlet widthb1 = 6 cm. The outlet radius r2 = 10 cm and outlet width b2 = 3 cm. Assuming 100% etticiency and considering 0.2m3/s flow rate, calculatea) the net head produced by the blowerb) the breaking horsepower in watt.(Take density of air Pair = 1.2 kg/m', gravity, g = 9.81 m/52)
Please help
100 mm 4. Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 60 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of u from the tangential direction, as shown in the figure. The length of each sprinkler arm is 0.45 m. Disregarding any frictional effects, determine the rate of rotation n of the sprinkler in rev/min for (a) 0 =0°, (b) 0 =30° r=0.45 m
Water of density ? =998.2kg/m3 flows through a fireman’s nozzle—a converging section of pipe that accelerates the flow. The inlet diameter is d1 = 0.100 m, and the outlet diameter is d2 = 0.050 m. The average velocity, momentum flux correction factor, and gage pressure are known at the inlet (1) and outlet (2). (a) Write an expression for the horizontal force Fx of the fluid on the walls of the nozzle in terms of the given variables. (b) Verify your expression by plugging in the following values: ?1 = 1.03, ?2 = 1.02, V1 = 3 m/s, P1,gage = 137,000 Pa, and P2,gage = 0 Pa.
A jet of water strikes a splitter and splits into two streams of equal velocity but unequal thickness. All jets have a width w (into the paper). Friction forces of the water stream on the splitter are negligible. Ignore the weight of the splitter. a) Use the integral mass conservation equation to find an equation for the thickness t of angled exit stream, t = f (h, a) b) Apply the momentum equation in the vertical direction to find an equation 0 = f(a).Hint: the net vertical force on the splitter is zero c) Find an equation Fx = f(p, V, w,h,a,0) for the horizontal force on the splitter
jet of water of diameter 100 mm strikes a curved plate at its center with a velocity of 15 m/s. The curved plate is moving with a velocity of 7 m/s in the direction of the jet. The jet is deflected through an angle of 150°. Assuming the plate smooth find: (i) Force exerted on the plate in the direction of the jet. (ii) Power of the jet, and (iii) Efficiency.
A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1 =0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q = 0.265 m^3/s, a water density ρ = 1.000 × 103 kg/m^3, a rotation speed n = 2.4 × 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2 , and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Find the velocity triangles just before the impeller inlet and just after the impeller outlet at a radius of r =0.09 m.
In the figure below, this "double" nozzle discharges water (at 10°C, density= 1000 kg/m3) into the atmosphere at a rate of 0.50 m3/s. The pressure at the inlet is to be 315612 Pa. If the nozzle is lying in a horizontal plane. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe (1) is 30 cm in diameter. The x-component of force (Rx) acting through the flange bolts is required to hold the nozzle in place is: Patm V3=26.1 m/s Patm VA=26.1 m/s Rx P=315612 Pa V,=7.07 m/s Select one: O a. 12.2 kN O b. 18.2 kN O c. 15.2 kN O d. 19.2 kN e 0E = 0
The pump-turbine system in the Figure draws water from the upper reservoir in the daytime to produce power for a city. At night, it pumps water from lower to upper reservoirs to restore the situation. For a design flow rate of 15,000 gal/min in either direction, the friction head loss is 17 ft. Estimate the power in kW: (a) extracted by the turbine and (b) delivered by the 1- Select coordinates and points 1 and 2 2- Write down your assumptions 3- Apply Energy Eq. and start finding P, V, and z for points 1 and 2 as well as head (h) values 4- Solve for unknown (1) Z₁ = 150 ft pump. Water at 20°C Pump- turbine (2) 2 Z₂ = 25 ft P1 V² + pg 2g P2 V + +Z2+hfriction + hTurbine - hpump [pressure head] 29 +Z1 = pg
Please correct answer