Express the given series using sigma notation 1 + x + x² + x³ + ... + x10

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: Convert to isometric drawing mark point A as the lowest point

A: use a 30-60 triangle to create the isometric  figure ng follow the left, front and top illustration…

Q: Use S = Last digit of your matric number and T= second last digit of your matric number. Example: if…

A: Given: S=2 , T= 0 To Find:  The enclosed area.

Q: 6. show all steps in detail, units and formulas please.

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: Calculate the Minimum Y distance on the drawing below: 1.000 C 2.000 Ø.995-1.000 I 6.00 0.008 MABC X…

A: given; net distance(Snet)=6tolerance in first circle(T1)=0.008net tolerance in x from both side…

Q: How do we write the position or displacement equations for any angle of  theta shown with blue…

A: Given:To find:Position or displacement equations.

Q: Calculate the Maximum Y distance on the drawing below: 1.000 O .510 O .500 O 2.009 C .460 2.000…

A: Maximum  Y distance is possible when the right side hole is having minimum diameter. The distance…

Q: How many basic dimensions are on the print shown in the figure provided?

A: Basic dimensions are theoretically exact dimensions that define the ideal size, location,…

Q: write .687+/- .0003 as a limit dimension

A:

Q: Some necessary dimensions are dimensions that are missing. missing from the following 3-view…

A: According to the details provided in the three views of the drawing, there is a hole of 2 units in…

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

A:

Q: Given the following mechanical engineer's scale, deter- mine the readings at A, B, C, and D. C - 10…

A: Note:- As per the guidelines of Bartleby, only one answer is allowed to answer, so please submit…

Q: in the given system, as the result of AB crank arm's spinning, F gear is starting to have an…

A:

Q: Determine if the following sketch is Over Defined, Under Defined, Fully Defined.

A: Given :-  Determine if the following sketch is Over Defined, Under Defined, Fully Defined.

Q: A rock is spit out of a fire. Its initial temperature is 414 degrees. After exactly 8 minutes, it…

A: Introduction: Newton's law of cooling, which is a function of the cooling constant and time, is…

Q: 37. Show the tolerance zone for the given slot. Superimpose the tolerance zone on the given drawing.…

A: Given, The tolerance for the offset is T=±0.02 units So, the thickness of the tolerance zone is…

Q: 1. For the following part sizes and geometric tolerances, determine the appropriate geometric…

A: (A) Pin, φ2.062-0.005+0.000  tolerance =upper limit - lower limit tolerance = 0.000-(-0.005)…

Q: Convert the bracket into an isometric drawing mark the corner marked A as the lowest point of the…

A: Approach to solving the question: To solve the question, identify corner A as the lowest point and…

Q: SolidWorks to create the parts.

A: I am using Solidworks to draw a 3-d object of the given problem.

Q: Draw the three standard orthographic views for the following object.

A: Draw the three standard orthographic views for the following object.

Q: c 2. How much money will be accumulated in 20 years from a deposit of $1500 every 6 months if the…

A: Years=20Deposit= $1500 every 6 monthInterest rate= 2.75% per monthEquations given:

Q: What's the median of the following points? x = Type your answer... [-3 3 4 2 -1 1 4 5]

A:

Q: Using the diagram, determine the minimum diameter for DIA B, in inches. DIA A 0 000 O 00016 BASIC…

A:

Q: Show the tolerance zone created by each of the given tolerance specifications. Superimpose the…

A: We have to show the tolerance zone created by each of the given tolerance specification. And,…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.