Answered: Explain working principle of a…

Engineering

Electrical Engineering

Explain working principle of a gyroscope with the help of a diagram. Give its applications.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Related questions

Q: SOLVE AND SHOW YOUR COMPLETE SOLUTION. ANSWERS SHOULD BE IN TWO DECIMAL PLACES. The armature of a…

Q: b) Figure 6 shows a moveable wire PQ across a magnetic field B with force F at a constant velocity…

A: Given : v=4.0 cm/s=0.04 m/sI=10 cm=0.1 mB=0.5 TR=0.8 Ω The magnitude of induced emf is given by:…

Q: What is the permeability and magnetic susceptibility of a superconductor

A: In this question we will write about permeability and magnetic susceptibility of superconductor...

Q: (a) the total reluctance of the flux path (iron plus air gap) (b) the current required to produce a…

Q: For a motor design, you need to design a solenoid coil that produces a magnetic flux density (B) of…

Q: Refer attached figure of an axial reluctance force actuator on Image 1. While ignoring core…

A: Given: An axial reluctance force actuator is shown in the figure below: The actuator is excited by…

Q: An electromagnet is used to support a solid piece of steel, as shown in the figure below. A force of…

Q: 4. Explain the operation of thermochemical energy storage system.

A: Thermal energy storage (TES) is an advanced method to store thermal energy and facilitate more…

Question

Explain working principle of a gyroscope with the help of a diagram. Give its applications.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer attached figure of an axial reluctance force actuator on Image 1. While ignoring core reluctances, find the reluctance force, F, if x = 0.004 m and I = 5 A using the atached force expression on attached image 2.
3.12 A carbon brush used to conduct current from the commutator of a DC generator has a length of 4 in. It must conduct a current of 400 A with a voltage drop not exceeding 2 V. Determine the cross-sectional area of this carbon brush. 3.13 Early DC machines use brass brushes instead of carbon brushes. The com- mutator bars do not last very long since brass is a rather hard metal. If a brass brush of the dimensions determined in problem 3.12 is used instead to conduct the same current, determine the voltage drop.
A P KN Refer to the figure. d₁ 0.9 m Force P is 60 kN and each force Q is 125 kN. Q KN B Add your answer Integer, decimal, or E notation allowed Q KN The diameter d₁ = 30 mm and diameter d₂ = 50 mm. d₂ 1.2 m What is the normal stress in rod BC in MPa? Round to the nearest integer and enter the magnitude only. C
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
In a 12-pole douplex lap wound dc armature, each conductor can carry a current of 50 amps. What is the related current of the armature?
help me provide a picture of a device that is used everyday with the concept of this image. And explain the mechanism and principles of the device's operation
O A. Bring out Four differences between the Thyristor and TRIAC. Q4) A. B. Describe the various methods of thyristor turn-on.
A)The left hand rule for a coil is such that if you were to hold a coil in your left hand with your fingers pointing in the direction of the electron flow, your thumb would point in the direction of thea) electron flow b) flow lines c) face of the north pole d) none of the above. B) What is a magnetic flux line?a) It is the space around a magnet or the space in which the magnetic forces act.b) It is the magnetic force that has a definite direction at all points along a curved line from the north to south pole.c) It is the ability of a magnetic material to be easily magnetized.d) none of the above C)It is believed that a magnetic material is .........a) consists of a single large magnetic molecule b) is composed of many tiny magnetic molecules c) consists of a single non-magnetic molecule d) none of the above
A thermistor which has an input of a temperature change, the output form is:Select one:a. Resistance O b. VoltageO c. HeatO d. Displacement O e. Magnetic fieldf. Capacitanceg. Current
A 10 pole d.c. machine has a lap wound armature. It has 600 conductors, each of resistance 0.05 ohm. What is the armature resistance
In this Exercise 6 we will explore laws critical to the study of electromagnetism. We will be using Simulation 3 (below) to explore how a moving magnet produces current in a nearby coil of wire. a. Magnetic field strength decreases as you get farther from the poles of the magnet. Does the flux through the face of the coil change as you move the magnet? Explain your answer. b. Why does the meter needle deflect? Is the deflection in accordance with Lenz’s Law? Justify your answer in terms of Lenz’s law and your above answers.
I want to know what temperature the cylinder will have inside. It's a heat transfer problem. current: 31 A voltage 42V Induction coil measurement: It has 1/8” OD and 0.03” wall thickness and will wrap around the cylinder and will have the same height as the cylinder.