Explain which kind of microstructures you expect to observe at room temperature if an iron-carbon alloy of eutectoid composition is cooled down following the red and blue curves. 800 727° 700 Coarse pearlite 600 a+ Fe, C Fine pearlite 50 y+a+ Fe, C 400 Bainite 300 200 so -Mo 100 1 min I hour 1 day 1 sec 102 105 10 103 104 0.1 Time, seconds

Explain which kind of microstructures you expect to observe at room temperature if an iron-carbon alloy of eutectoid composition is cooled down following the red and blue curves. 800 727° 700 Coarse pearlite 600 a+ Fe, C Fine pearlite 50 y+a+ Fe, C 400 Bainite 300 200 so -Mo 100 1 min I hour 1 day 1 sec 102 105 10 103 104 0.1 Time, seconds

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the temperature of the liquid and gas increases by the same amount, what effect does this have on the viscosity for each of them?
(a) What is the dimension of an area moment of inertia?(b) If the thickness of a piezoelectric cantilever beam increases, does the natural frequencyincrease or decrease?(c) Both the thickness and width of a piezoelectric cantilever beam can change the natural frequency. Which parameter (thickness or width) will lead to the natural frequency change more significantly? Briefly explain your answer.
A 4 meter long steel plate with a rectangular cross section (10 mm x 50 mm) is resting on a frictionless surface under the sun. The plate temperature is measured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is measured to be 5°C. The steel has a modulus of elasticity equal to 200 GPa and a coefficient of thermal expansion equal to 1.1x10-5/°C. a. What is the length of shrinkage b. What tension load is needed to return the length to the original value of 4 meters? c. What is the longitudinal strain under this load?
Two hypothetical metals are created with different elements that have the same atomic mass (g/mole) and the same atomic radius. Metal A has a densityof 9.50 g/cm3 and metal B has a density of 8.73 g/cm3. If one of these metals has a BCC lattice structure and the other has an FCC lattice structure, identify the structure that corresponds to each of one of them. Justify your answer.
Figure P2.33 shows a portion of the H,O-NaCl phase diagram. 10 Liquid (brine) Salt Ice + -10 F liquid (brine) liquid (brine) -20 Ice + salt -30 NaCI 10 20 30 H2O 100 90 80 70 FIGURE P2.33 Composition, weight % a. Using the diagram, briefly explain how spreading salt on ice causes the ice to melt. Show numerical examples in your discussion. b. At a salt composition of 10%, what is the temperature at which ice will start melting? c. What is the eutectic temperature of the ice and salt combination? Temperature, °C
For a nonwetting liquid, such as water, the surface is convex since the force of cohesion will be greater than that of adhesion. Water is non-Newtonian. Temperature at which water has the highest density is usually taken as 4°C(39.2°F). PROBLEM 1: A closed tañk whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. a. Determine the pressure at the interface of carbon tetrachloride and syrup. * Your answer b. Determine the difference in pressure between the interface of water and syrup and the interface of carbon tetrachloride and syrup.
sodium fluoride and aluminum sulfate Туре: double displacement single displacement Molecular: Total lonic: Net lonic: If single displacement What is oxidized? What is reduced? How can you tell? How can you tell?
List the 5 classes of the crystal-chemical classification of minerals, giving a mineral example for each class
Calculate the magnitude and direction of the forces acting on each element in the lattice system shown in the figure.