Answered: Explain the purpose of the wheel rim…

Engineering

Mechanical Engineering

Explain the purpose of the wheel rim drop center and safety ridges.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter40: Drive Axles And Differentials

Section: Chapter Questions

Problem 4RQ: What type of floating axle has one wheel bearing per wheel on the outside of the axle housing?

See similar textbooks

Related questions

Q: Road test Report is Overhaul all four-wheel brakes and the Universal joints After the maintenance…

A: Option - B , D => After operation is completed the road test report will happen to check the…

Q: What type of floating axle has one wheel bearingper wheel on the outside of the axle housing?

A: A full floating axle has one wheel bearing per wheel on the outside of the axle housing.…

Q: What type of axle merely supports the vehicle load and provides a mounting place for the wheels?

A: Axles are very important parts of an automobile. These axels are used to supports the loads and…

Q: explain the purpose of the the wheel rim drop center and safty ridges ?

A: Purpose of the wheel rim drop center: The wheel rim drop center is the center section which is lower…

Q: Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight .…

A: technician A is wrong and technician B is saying correctly.

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: 49.--------------occurs When the clutch is fully engaged, the driven disc does not rotate at the…

A: Clutch is a machine component that connects/disconnects the engine from the transmission drive. It…

Q: What is the correct sequence for adjusting alignmentangles during a four-wheel alignment?

A: Given Data : Adjusting alignment angles during four wheel alignment.

Q: How are problems normally first noticed with the differentialand drive axles?

A: SYMPTOMS OF A DAMAGED DIFFERENTIAL Other components may show signs of damage when your vehicle has…

Q: When removing the balance shaft assembly: tech a inspects the bearings for unusual wear or damage.…

A: Balance shafts are serviced in the same way as crankshafts.there are two main causes of removing or…

Q: Why do we need to diagnose the transmission/transaxle failure?

A: It is very important to diagnose the transmission failures in any vehicle.There are many factors…

Q: Technician A says that the front bearing assembly locknuts for RWD vehicles are typically heavily…

A: A high torque for maintaining the bearing adjustment is required in the FWD vehicles and not the RWD…

Q: 108) Technician A says that engine management malfunctions may be misinterpreted as transmission…

A: Engine management malfunctions can be seen by malfunction indicator lamp . this indicator shows that…

Q: When adjusting a vehicle to counter the effect of road crown, what is the adjustment would you…

A: -Adjust the left front wheel with slightly less positive caster When adjusting a vehicle to counter…

Q: what is the first alignment angle to be adjusted when performing a front wheel alignment? A. CAMBER…

A: To determine: The first alignment angle to be adjusted when performing a front wheel alignment…

Q: Design and explain fatigue test setup for a crankshaft ?

A: Consider the diagram shown below for the crankshaft setup, For the resonance fatigue test…

Q: What is the job of wheel cylinder stops?

A: Wheel cylinder is a component of a hydraulic drum brake system.it locates in each wheel and…

Q: structural analysis and assembly of gearbox

A: Structural Analysis of gearbox Nature of loading within the various components of a gear box is an…

Q: Technician A says a wheel alignment rack should include rear slip plates. Technician B says a four…

A: During the alignment lift operation, it is necessary to take off slip plates. To give a better wheel…

Q: 1. Technician A says that the use of firmer, ure- thane bushings in the suspension improves the…

A: As per the Bartleby Answering guidelines we are supposed to answer first three questions. Please…

Q: Q-3 ) The distance between the steering pivots of a Davis steering gear is 1.5 m.. The wheel base…

A: Data given - Width of front axle (w) = 1.5 m Wheel base (l )= 2.50 m

Q: cylinder failed due to static load or cyclic load

A: The failure occurs in wheel cylinder due to cyclic loading.

Q: History of manual transmission

A: The first manual gearbox was created by Emile Levassor and Louis-Rene Panhard. The original…

Q: List six checks that should be carried out when inspecting camshafts

Q: Technician a says radial ply tires are more rigid in the sidewall area than bias ply tires.…

A: Technician A is wrong because bias-ply tires have fibres of nylon arranged in a diagonal manner to…

Q: 49.--------------occurs When the clutch is fully engaged, the driven disc does not rotate at the…

Q: Out of the camber and caster, which is measured first and why? How the camber angle can be adjusted…

A: Camber angle is the angle which is measured in the front elevation in-between the wheel plane &…

Q: In what direction must the bottom of a tire andwheel assembly be moved to add more positivecamber?

A: Given Data : Bottom of tire Wheel assembly

Q: What type of brake uses the inside of each rear wheel hub and rotor assembly as a parking brake…

A: Brake drum absorbs a lot of heat and dissipate into the air. Due to the continuous heating and less…

Q: If one wanted to calculate braking friction on the braking pad, one would need to know Question 1…

A: Option d is correct.

Q: What is the principle of the balancing act in tires?

A: The tyre will roll smoothly when all regions of the wheel-tire unit are as evenly weighted as…

Q: what the tire wear pattern will result from excessive negative chamber?

A: Solution:

Q: raking torque applied?

A: Given; A force, F=400 NApplied to the brake drum of diameter, d=0.5 mWrapping angle,…

Q: The worm wheel rim is made of copper for A.Easy to manufacture B.Stable transmission C.High…

Q: 1. Torque converter it is part of brake axle clutch Automatic transmission O O

A: Dear student, According to the guidelines I am allowed to answer only one…

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

Explain the purpose of the wheel rim drop center and safety ridges.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

explain the purpose of the the wheel rim drop center and safty ridges ?
Define dynamic and static wheel balance.
While performing a prealignment inspection: Technician A says that improper front-wheel bearing adjustment may affect wheel alignment angles. Technician B says that worn ball joints affect only the camber angle. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
Technician A says that the front bearing assembly locknuts for RWD vehicles are typically heavily torqued to maintain the bearing adjustment. Technician B says that the axle nuts for FWD wheel bearing assembly is often staked in place to maintain its specified torque. Who is correct?
Is the wheel cylinder failed due to static load or cyclic load?
Wheel A: 32A60H8V Wheel B: 39C100L6V What type of bond is used for both wheels?
what the tire wear pattern will result from excessive negative chamber?
Hello, I am trying to study for a test and found this practice review but I'd like to be able to check my work. Can someone help answer some of these questions? Thank you
I need structural analysis and assembly of gearbox . instructions are given please do it as mentioned
Technician A says a wheel alignment rack should include rear slip plates. Technician B says a four wheel alignment can be performed on a 2 wheel alignment machine with some extra work. who is correct?
When servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricants
While driving straight, a FWD car pulls to the right. The most likely cause is. more positive camber on the left front wheel compared to the right front wheel sagged front springs and improper front-wheel toe setting less positive caster on the right front wheel compared to the left front wheel the SAI on the right front wheel is 1*A degrees more than the SAI on the left.