Exercise: A transmission line operating at 500 MHz has Zo = 800, a= 0.04 Np/m, B= 1.5rad/m. Find the line parameters R, L, G, and C.• R = 3.2 Q/m,•L = 38.2 nH/m,• G = 0.5 mS/m,• C = 5.97 pF/m.R+jwLZo =Y= a+jßG+jwC%3D= (R + j@L)G + jwC)26

Answered: Image /qna-images/answer/fbe7026d-cd10-4415-8d72-d862010e86d2.jpg

Answered: Exercise: A transmission line operating…

Exercise: A transmission line operating at 50 rad/m. Find the line parameters R, L, G, and • R= 3.2 0/m, •L = 38.2 nH/m, • G= 0.5 mS/m, • C = 5.97 pF/m. R+jwl %3D G+jwo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 132 Kv, 50 Hz, 3-phase tensmission line delivers a load of 5omw at 08 lagging Pf. the transmission line have: A-D: 0 95 Lu" 190 C-0. Ool5 B-96 using Nominal Tto Calculade: regulation of the line and charging Curent?
How do you derive the Telegrapher's Equations for a lossy transmission line? Why is it the bottom equation?
(please solve with complete steps both parts .i will give thumbs up)
please very quickly
3. A 132 kV, 50 Hz, 3-phase transmission line delivers a load of 50 MW at 0-8 p.f. lagging at the receiving end. The generalized constants of the transmission line are : A = D = 0-95 21-4° ; B = 96 278° ; C = 0-0015 z90°.Find the regulation and charging %3D current. Use Nominal-T method.
3 A 3-phase, 50 Hz transmission line 100 km long, Load current i 5A at 0-9 p.f.lagging and at 110 kV. The resistance and reactance of the line per phase per km are 0-2 Q and 0-42 respectively, while capacitance admittance is 2-5 * × 10- 6 siemen/km/phase. then magnitude of V1 is
A lossless transmission line has a capacitance per unit length of 64PF/m and an inductance per unit length of 1µH/m. The load impedance ZL is purely resistive. Both the load impedance and the generator impedance are 50 Ohms. the characteristic impedance and the propagation velocity O 1502 , 2.25*10®m/s O 1250, 1.25*108m/s O 1250 , 2.25*10°m/s 1500, 1.25*108m/s
• Draw a Lattice diagram each for transient currents and transient voltages that are propagating at the speed of 1.25 x 108 a, m/s for 10 us along a 250 m length transmission line. Note that the transmission line is with characteristic impedance of Zo=754-55° 2 and terminated with an short circuit load Also, the supply is with Vg = 15410⁰ V and Zg = 145x25⁰ 2.
5. Consider a transmission line with characteristic impedance Zo=50, length = 600 m, and prop- agation velocity v = Vcc = c = 3 x 108 m/s. A voltage source f(t) with an internal resistance R₂= 25 is connected to one end of the T.L. (at z = 0) and the other end (z = 1) is terminated by a load resistance RL = 50/30. a) Construct a bounce diagram to determine the voltage, V(z, t), variations on the line for 0 <=<1 and 0 < t < 10 µs for f(t) = 8(t). Write the values of Tg, IL, and I, explicitly and make sure to label both axis of the bounce diagram properly in terms of m and us units and indicate the amplitudes of traveling impulses next to the impulse trajectory lines. b) Write your expressions for V(,t) and I(,t) as weighted sums of appropriately delayed impulses 8(t) for 0 < t < 10 µs.
Q) A transmission line of negligible loss has a characteristic impedance of 600 Q. Calculate the VSWR along the line when it is terminated by an impedance of (400+j300) . What is the VSWR if the load is changed to a purely resistive one of 500 0?
!EMERGENCY! Normalized admittance values zI= 0.4 - j0.3 with two load impedances connected in parallel with a 50 cm long coaxial line insulated with dielectric (€1 = 3) It is connected to a source with an operating frequency of 1 GHz. Find the distance of the voltage max and min to the load and the normalized input impedance of the line.
A 470 kV, three phase transmission line with a 350 km length. The series impedance Z = (0.078+j0.34) 0/ph/km and shunt admittance y = (j2.8 x e(-6)) S/ph/km. Evaluate the equivalent Tt-model and T-model parameters.