Exercise : A 555 timer configured to run in the astable mode (oscillator) is shown in Figure below. Determine the frequency of the output and the duty cycle. [Answers: 5.64 kHz, 59.5%] +5.5 V R 2.2 kn RESET Vce DISCH 555 THRESH OUT 4.7 kN TRIG CONT GND 0022 μF 0.01 µF

Q: Q) The frequency is relating to time period--- Square proportional. O Not related. Directly…

A: In this question Choose the correct options What is relation between frequency and time period.

Q: 1. Are the theoretical calculations and measured values are equal? Explain?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Q-01 (What is called Buck Converter & What is called Boost Converter?)  give two examples for each.

A: Explanation: The buck converter is a ubiquitous DC-DC converter that correctly converts an excessive…

Q: do you have any other method to solve this problem??

A: In the given circuit,we need to find above mentioned parameters.

Q: Solve for the number of luminaires. The type of structure is an indoor basketball court having a…

A: It is given that: Length (l) = 40 feet Width (w) = 60 feet Height (h) = 17 feet ceiling cavity…

Q: Q1: Fill in the blanks with appropriate words. 1. I . her for everything she . (A) thanking / did…

A: Use appropriate parts of speech and proper tenses to solve these

Q: What can you say about the topic: PHILIPPINE ELECTRICAL CODE 1

A:

Q: A single-phase 60-Hz power line is supported on a horizontal crossarm. The spacing between…

A: Distance between power conductors is 8ft.The distance between telephone conductors is 2ft.

Q: Vending machine. After joining a circuit design company, you are asked to design the control circuit…

A: We need to design the control circuit of a vending machine that sells a type of bottled soft drink.…

Q: What information is contained in the specification K, 10,000

A: Kp stands for the position error constant for the step input function.  here, Kp = 10000

Q: A combinational switching network, has four inputs (a,b,c,d) and one output. The output is at logic…

A:

Q: An electric train system (ETS) in Japan with a span of 10 miles long is connected to a two…

A:

Q: 1.verify (Kc) and (KUL)) ?

A:

Q: 17. A 15 A, 125 V, 10 receptacle installed of a dwelling unit does not require GFCI protection. A.…

A: Solution of question (18): Four options are given in the question. We need to choose the correct…

Q: 6 Choose the correct form. 1 I went to the shops for to buy / for buy / to buy some shoes. 2 Do you…

A: We are authorized to answer three subparts at at a time since you have not mentioned which part you…

Q: The imaginary power of any circuit is transferred in both directions The power triangle represents…

A:

Q: Is there an interference between multiple users in telephone system communication? If your answer is…

A: Ans .  No

Q: Which of the following do not apply to a primitive network? (a) It has two terminals. (b) It is…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: The is the construction of the available n- and p-type materials, that was constructed as our first…

A: 1)Diode  2) Reverse bias

Q: Don't use ai to answer I will report your answer Solve it Asap with explanation... What is a wind…

A: We should separate what a wind rose is and its importance in wind energy analysis in more…

Q: QI\ Define standard of measurement and explain categories that standard of measurement classified to…

A: Here we will define standard of measurement and we will also explain the categories of standard of…

Q: Please show the work in between the rearranged formula and the answer

A: Given: Calculate the S/N in dB if the passband circuit is 48kHz to 64kHz and the maximum bit rate is…

Q: > A point source emits 30 W of sound. A small microphone has an area of 0.75 cm is placed 10 m from…

A:

Q: d) None of these. 5. Materials which easily allow the passage of electric current are known as: a)…

A: Answer 2- The power is defined as a rate of doing work.  So, option (c) is correct.   Answer 4- An…

Q: State and prove Baye's theorem

A:

Q: Provide Your Answer as  letter A if the first statement is True , Letter B if the second statement…

A: Given the statements as follows- 1. The passing general average rating shall be seventy percent…

Q: Signal presentation element is used to transmit the signal from the plant to the observer. True or…

A:

Q: Look at the photo and answer the questions

A:

Q: if i use Voltage division instead of nodal analysis. where do you suggest i start, and How do I…

A:

Q: can you do the other part of the question too

A: Since you have posted multiple questions with multiple sub-parts, we will provide the solution only…

Q: 1. The pizza is .. 2. The phone is very . 3. Our house is very 4. I do not have much 5. baghdad is a…

A: 1) DELICIOUS 2)HELPFUL 3)LOVELY 4)DOLLARS

Q: In an electrical system, each of the service entrance conductors has an area of 750 kcmil. The size…

A: Given: In an electrical system, each of the service entrance conductors has an area of 750 kcmil.

Q: Could you answer this question in details and giving examples if possible. Thanks a lot.  - Explain…

A: The Controller Area Network (CAN bus) is a standard automotive bus system designed to allow…

Q: im still confused on how 5/6 is part of the answer can someone explain

A: When the KVL is applied at mentioned node, it gives the equation V-802000+V-04000+V-012000=0. On…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.