Exercise 2. [Delay estimation] Adapt from Kurose 7th edition, chapter 1 problem P10,P11. Consider a packet of length L that begins at end system A and travels over three links to a destination end system. These three links are connected by two packet switches. Let d;, s;, and R; denote the length, propagation speed, and the transmission rate of link i, for i=1,2,3. The packet switch delays each packet by dproc. Assuming no queuing delays, in terms of d;, si, and R;, (i=1,2,3), and L. 1. What is the total end-to-end delay for the packet? 2. Suppose now the packet is 2,500 bytes, the propagation speed on all three links is 2.5 * 10°m/s, the transmission rates of all three links are 2 Mbps, the packet switch processing delay is 4 msec, the length of the first link is 3,000 km, the length of the second link is 2,000 km, and the length of the last link is 1,000 km. For these values, what is the end-to-end delay? 3. In the above problem, suppose R1 = R2 = R3 = R and dproc = 0. Further suppose the packet switch does not store-and-forward packets but instead immediately transmits each bit it receives before %3D waiting for the entire packet to arrive. What is the end-to-end delay?

Exercise 2. [Delay estimation] Adapt from Kurose 7th edition, chapter 1 problem P10,P11. Consider a packet of length L that begins at end system A and travels over three links to a destination end system. These three links are connected by two packet switches. Let d;, s;, and R; denote the length, propagation speed, and the transmission rate of link i, for i=1,2,3. The packet switch delays each packet by dproc. Assuming no queuing delays, in terms of d;, si, and R;, (i=1,2,3), and L. 1. What is the total end-to-end delay for the packet? 2. Suppose now the packet is 2,500 bytes, the propagation speed on all three links is 2.5 * 10°m/s, the transmission rates of all three links are 2 Mbps, the packet switch processing delay is 4 msec, the length of the first link is 3,000 km, the length of the second link is 2,000 km, and the length of the last link is 1,000 km. For these values, what is the end-to-end delay? 3. In the above problem, suppose R1 = R2 = R3 = R and dproc = 0. Further suppose the packet switch does not store-and-forward packets but instead immediately transmits each bit it receives before %3D waiting for the entire packet to arrive. What is the end-to-end delay?

Computer Networking: A Top-Down Approach (7th Edition)

7th Edition

ISBN:9780133594140

Author:James Kurose, Keith Ross

Publisher:James Kurose, Keith Ross

Chapter1: Computer Networks And The Internet

Section: Chapter Questions

Problem R1RQ: What is the difference between a host and an end system? List several different types of end...

See similar textbooks

Related questions

Q: Assume a small communication network, consisting of two user stations and a base station (BS). The…

Q: A sender with window size (W=3) is connected to a selective repeat receiver by a link with…

A: Solution: Given, the window size (W) of the sender is 3, the bandwidth of the link is 106…

Q: Consider a router that transmits bits onto a transmission medium at the rate of 2 Mbps. Let the link…

A: Given: Bandwidth = 2 Mbps => 2 *106 bits/sec Distance = 3 km Speed = 3 * 108 meter/sec…

Q: 1. Consider a 10Mbps shared Ethernet with Bus Topology. The total length of the cable is 2000m and…

A: Ethernet technology is a popular networking technology that allows several devices to connect with…

Q: e. Suppose dprop is greater than dtrans. At time t = durans, where is the first bit of the packet?…

A: Requested answers are given below:

Q: (d) Given the MPLS network shown below where R1 is the ingress router and R7 is the egress router.…

A: It is given that R3 and R6 are connected through R4 and R5. R4 and R5 might belong to another…

Q: Computer A is sending a 10 MByte long file to Computer B via packet-switching over two consecutive…

A: Computer networking which refers to interconnected computing devices that can exchange data and…

Q: Computer A is sending a 100 kByte long file to Computer B via packet-switching over two consecutive…

A: Here in this question we have given that Total size = 100kB Bandwidth= 10Mbps. Link distance…

Q: This elementary problem begins to explore propagation delay and transmission delay, two central…

A: As per our company guidelines only three sub parts will be answered. So, please repost the remaining…

Q: Equation 1.1 gives a formula for the end-to-end delay of sending one packet of length L over N links…

A: A packet is a discrete chunk of data transferred via a network, like the Internet or a local area…

Q: Computer A is sending a 10 MByte long file to Computer B via packet-switching over two consecutive…

A: Computer Networks which refers to the set of the computers which are connected through the medium…

Q: Computer A is sending a 100 kByte long file to Computer B via packet-switching over two consecutive…

A: Given that, Size of the file= 100 KB Bandwidth of the link= 10 Mbps Distance of each link= 1000 Km…

Q: Computer A is sending a 10 MByte long file to Computer B via packet-switching over two consecutive…

A: Given that, Length of file= 10 MB Length of packet= 1480 bytes Bandwidth of the link= 100 Mbps…

Question

Exercise 2. [Delay estimation] Adapt from Kurose 7th edition, chapter 1 problem P10,P11.
Consider a packet of length L that begins at end system A and travels over three links to a destination
end system. These three links are connected by two packet switches. Let d;, s;, and R; denote the length,
propagation speed, and the transmission rate of link i, for i=1,2,3. The packet switch delays each packet
by dproc. Assuming no queuing delays, in terms of d;, si, and Ri, (i=1,2,3), and L.
1. What is the total end-to-end delay for the packet?
2. Suppose now the packet is 2,500 bytes, the propagation speed on all three links is 2.5 * 10°m/s, the
transmission rates of all three links are 2 Mbps, the packet switch processing delay is 4 msec, the
length of the first link is 3,000 km, the length of the second link is 2,000 km, and the length of the
last link is 1,000 km. For these values, what is the end-to-end delay?
3. In the above problem, suppose R1 = R2 = R3 = R and dproc = 0. Further suppose the packet switch
does not store-and-forward packets but instead immediately transmits each bit it receives before
waiting for the entire packet to arrive. What is the end-to-end delay?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

Suppose that KJ sends 3596 back-to-back packets, with each packet composed of 14,000 bits, to TA over 5 links (shown below). Suppose that the transmission rate of each link is 70,000 bits/sec (bps). Consider the routers to be store-and-forward routers. In such a scenario, find the endto- end delay of sending all the packets to TA (i.e., the time needed for the last bit of the last packet to arrive at TA since KJ starts transmitting the first bit of the first packet). Note, consider only the transmission delay that occurs in sending packets in your analysis. Show the steps used for derivation in detail. 70,000 bps 70,000 bps 70,000 bps 70,000 bps 70,000 bps KJ Router 1 Router 2 Router 3 Router 4 ТА
Please give me correct solution.
Consider a packet of length L that begins at end system A and travels over three links to a destination end system. These three links are connected by two packet switches. Let d, s, and R denotes the length, propagation speed, and the transmission rate of link i, for i=1,2,3 . The packet switch delays each packet by d . Assuming no queuing delays, in terms of d, s , R, (i=1,2,3), and L, what is the total end-to-end delay for the packet? Suppose now the packet is 1,500 bytes, and the propagation speed on all three links are 3125km/sec, 10000 km/sec, and 3333km/sec respectively. The transmission rates of all three links are 2 Mbps, the packet switch processing delay is 3 msec, the length of the first link is 5,000 km, the length of the second link is 4,000 km, and the length of the last link is 1,000 km. For these values, what is the end-to-end delay? In the above problem, suppose R1=R2=R3=R and dproc=0. Further, suppose the packet switch does not store-and-forward packets but…
Protocol 6's frame arrival code includes a part for NAKs.If the incoming frame is a NAK and another condition is satisfied, this section is called.Give an example of a situation in which the existence of this other condition is critical.
Computer A is sending a 10 MByte long file to Computer B via packet-switching over two consecutive 100 Mbps links of 2000 km length each.Assume that the signal propagation speed on both links is 2 x 108 m/s.Furthermore, assume that the maximum length of a packet is 1480 bytes and that Computer A fills each packet to the max, if possible. How long (in seconds) does it take Computer A to send out one packet of maximum length on the first link?
Computer A is sending a 100 kByte long file to Computer B via packet-switching over two consecutive 10 Mbps links of 1000 km length each.Assume that the signal propagation speed on both links is 2.5 x 108 m/s.Furthermore, assume that the maximum length of a packet is 1500 bytes and that Computer A fills each packet to the max, if possible. How "long" (in meters) is one bit on link 1?
Consider a router that transmits bits onto a transmission medium at the rate of 2 Mbps. Let the link be 3 km in length, and bits propagate through the transmission medium at the speed of (approximately) 3x10^8 meters/sec. What is the transmission delay in seconds to transmit a packet of size 2,0o0 bits onto the link? a. 1x10^-5 seconds O b. .001 seconds с. 1 second d. -4 seconds
Assume that an end-to-end communications system is made up of three networks with date rate in Mbps ρ1, ρ2, and ρ3, respectively. Ignoring the other delay components, what is the total end-to-end delay to transmit a packet size of λ?
show step by step
To ensure the quality of service, especially for multiple applications, regulating the rate at which packets are sent to the network is an important strategy. The leaky bucket is just one of such mechanisms. A flow of packets is said to conform to the leaky bucket specification (r, b), where r is the average rate and b is the burst rate, if the number of packets arriving at the leaky bucket is less than r*t + b in every time interval of t. What is the implication of that? What will happen if the number of packets arriving at the leaky bucket is equal to or greater than r*t + b?
In TCP Vegas, the calculation of Actual Rate is done by dividing the amount of data transmitted in one RTT interval by the length of the RTT. (a) Show that for any TCP, if the window size remains constant, then the amount of data transmitted in one RTT interval is constant once a full window-full is sent. Assume that the sender transmits each segment instantly upon receiving an ACK, packets are not lost and are delivered in order, segments are all the same size, and the first link along the path is not the slowest. (b) Give a timeline sketch showing that the amount of data per RIT above can be less than Congestion Window.
In a two-phase, total-order multicast system, messages are sent in the following sequence from node S to G1 and G2. G1 and G2 are the members of the group. S sends m1 to G1 S sends m1 to G2 S sends m2 to G2 S sends m2 to G1 Use the basic implementation of the Lamport clock. The clock s at each node start at: S: 4, G1: 6, G2: 1. Show the exchange of messages and their acknowledgments in a clock diagram using the basic implementation of Lamport's clock. In which order and at what times are m1 and m2 delivered?