(d) Given the MPLS network shown below where R1 is the ingress router and R7 is the egressrouter.R1R2R3R6R7R4R5 is the Label Switching Path (LSP) for this network, where R3 and R6 are notdirectly connected routers. Let Lij be the label value for the packet sent from router Ri to routerRi, (e.g., L12 is the label value for packet sent from router 1 to router 2).What would be the label(s) in the packet sent by the following routers: (1) R2 (2) R3 (3) R5Show all labels that would be contained in the packet. Assume penultimate hop popping is beingused. Show your answer as follows:Label 1Label 2Router iData LinkIPDataHeaderHeader

It is given that R3 and R6 are connected through R4 and R5. R4 and R5 might belong to another…

(d) Given the MPLS network shown below where R1 is the ingress router and R7 is the egress router. R1 R2 R3 R4 R5 R6 R7 is the Label Switching Path (LSP) for this network, where R3 and R6 are not directly connected routers. Let Lij be the label value for the packet sent from router Ri to router Rj, (e.g., L12 is the label value for packet sent from router 1 to router 2).

(d) Given the MPLS network shown below where R1 is the ingress router and R7 is the egress router. R1 R2 R3 R4 R5 R6 R7 is the Label Switching Path (LSP) for this network, where R3 and R6 are not directly connected routers. Let Lij be the label value for the packet sent from router Ri to router Rj, (e.g., L12 is the label value for packet sent from router 1 to router 2).

Computer Networking: A Top-Down Approach (7th Edition)

7th Edition

ISBN:9780133594140

Author:James Kurose, Keith Ross

Publisher:James Kurose, Keith Ross

Chapter1: Computer Networks And The Internet

Section: Chapter Questions

Problem R1RQ: What is the difference between a host and an end system? List several different types of end...

See similar textbooks

Similar questions

Consider the network shown below, and Dijkstra's link-state algorithm. Suppose that Dijkstra's algorithm has been run to compute the least cost paths from node E to all other nodes. Now suppose that source node E has a packet to send to destination node A. What is the first router to which E will forward this packet on its path to A? F A 3 2 B C 4 D 10 4 E 4 2
Consider the datagrams of each layer in the TCP/IP model, e.g., Frame at the Link Layer, Packet at the Internet Layer. Explain the functioning of the following protocols based on their datagram header fields only. Note: You do not need to describe the header field but based on the header field, explain how the protocol works, e.g., Acknowledgement field in a TCP Header is responsible for providing reliable data transfer and in case of data loss or ACK not received, segment is re-sent. You do not need to consider every field of the headers but wherever there are more than 4 fields, then based on 5 fields, describe its functioning, if less than or equal to 4 fields then consider all the fields. Ethernet Frame 11 Frame IPv4 Packet IPv6 Packet TCP Segment UDP Segment HTTP
1. Consider a path from host A to host B through a router X as follows: A- -X-B The capacity of the link AX is denoted Ra, while the capacity of the link XB is denoted Rb in units of [bits/s]. Assume that Ra Ri. Is it possible that the second packet queues at input queue of the second link? Explain. Now suppose that host A sends the second packet T seconds after sending the first packet. How large must T be to ensure no queueing before the second link? Explain.
Consider a packet of length L that begins at end system A and travels over three links to a destination end system. These three links are connected by two packet switches. Let d, s, and R denotes the length, propagation speed, and the transmission rate of link i, for i=1,2,3 . The packet switch delays each packet by d . Assuming no queuing delays, in terms of d, s , R, (i=1,2,3), and L, what is the total end-to-end delay for the packet? Suppose now the packet is 1,500 bytes, and the propagation speed on all three links are 3125km/sec, 10000 km/sec, and 3333km/sec respectively. The transmission rates of all three links are 2 Mbps, the packet switch processing delay is 3 msec, the length of the first link is 5,000 km, the length of the second link is 4,000 km, and the length of the last link is 1,000 km. For these values, what is the end-to-end delay? In the above problem, suppose R1=R2=R3=R and dproc=0. Further, suppose the packet switch does not store-and-forward packets but…
Each active interface of Distance vector gets frequent transmissions of the whole routing table that Distance vector maintains. The link status protocol broadcasts information about the state of a router's own connections to all other routers in the network. Each statement has two ideal examples that show how the Link state and the Distance vector may be utilized in a number of circumstances.
A protocol stack used by many applications is to use TCP at the transport layer and IP at the network layer. The ICMP protocol is also used to report on problems encountered by IP. A) The IP protocol provides a service referred to as "best effort". Describe the services of IP and potentially ICMP protocol, with respect to flow control( ensuring the sender does not overwhelm the receiver). B) Describe the services TCP provides with respect to flow control and explain the mechanisms it uses to overcome the deficiencies of IP.
2. Now suppose there are two links between source and destination, with one router connecting the two links. Each link is 5,000 km long. Again suppose the MP3 file is sent as one packet. Suppose there is no congestion, so that the packet is transmitted onto the second link as soon as the router receives the entire packet. What is the end-to-end delay?