Example Height of instrument equal to 25.33 m and staff reading shown in figure below: central staff 2.36 m , right staff 3.17 m and left staff 1.89 m and the formation level is 24.07. Find the depth of fill for three points and the distance of the two pegs A and B from the center. if the formation width (width of proposed road way) is 6 m and side slope (1:2) CL 1.89 2.36 3.17 3m 3m 1 Ha 2 A Hb H.I=25.33 F.L= 24.07 DA DB Datum

Q: Given traffic flows for each lane group at a T junction shown in Figure below. The saturation…

A: Critical lane volume for each phase: P1: 500, P2: 250, P3:150 Sum of criticial lane volume,ΣVc =…

Q: 13. - should be located to withdraw water from slig below the surface in order to avoid sediment in…

A: The intake structures are used to safe withdrawal of water from the source, which will be discharged…

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen…

A: As per the Guidelines of Bartleby We are supposed to answer only first three subparts. Ultimate…

Q: QUIZ: Determine the reactions at the supports A and B of the beam shown in figure. 6 kN/m 3 kN/m

A: Free Body diagram of the given problem:

Q: Use the method of joints to determine the force in each member of the truss shown in the figure…

A: Let height be H43H+34H = 82512H = 8H = 3.84 Calculate Support Reactions ΣFY=0AY+CY = 20sin45°AY+CY =…

Q: We found that the Reynolds and Froude numbers Were important? discuss it

A: Reynolds number Froudes number Both numbers are widely used in fluid behaviour study.

Q: P1. Determine the distance x measured from the y axis to the centroid of the area of the iangle…

A:

Q: How to convert a value from the kips unit to a value in the ib unit

A: Brief concept introduction- Kips and lb are the two major units that are used for the measurement of…

Q: If the value of the atmospheric pressure reading using the barometric gauge is (750 mm) and the…

A:

Q: Q3) For the circular arch shown in the figure, compute the value of "P " such that the vertical…

A:

Q: Q12 A seismic survey was carried out for a large project to determine the nature of the substrata.…

A:

Q: Q2) Find the vertical detlection at D and rotation at B in terms of El by the unit-load method for…

A: In the virtual load or unit load method, a unit load is applied on the point where deflection and…

Q: Q1: A tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20…

A: Given that,  gage length = 50 mm diameter = 20 mm loat at 0.2% yield point = 100,000 N gage length…

Q: Solid Mechanics Set up the appropriate equation that is used to solve for the moment of inertia…

A:

Q: 30 F2 = 300 N F1 = 250 N |3D 60° A 2 m -3 m- 4 m B F3 = 500 N Determine the moment of each of the…

A:

Q: Prob.7. Workout the depreciated replacement cost of a building having the following particulars by…

A: Given that, Total life of building(n)  = 80 years  Built-up area = 400m² Total life of building in…

Q: The beam ABC, fixed at A and roller supported at B, is loaded as shown in Fig.1. Select the…

A:

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A:

Q: 17.6 A solid steel shaft 3 in. in diameter and 4 ft long is fixed at one end and free at the other,…

A: Given data  Diameter of shaft =3 in  Length of shaft = 4 ft  Axial tensile force = 50000 Lb

Q: From your graph, plotting the yield stress against 1/vd, you found that oo 69 MPa and k, = 0.8…

A:

Q: 2. Draw the axial force diagram of the bar. 20 35 45 30 (kN)

A:

Q: Q/ For the rectangular footing with dimensions (3*6) Show in figure (4). Calculate the immediate…

A: Given data:- Dimension of rectangular footing is 3×6 m.

Q: mine the resultant couple e into x and y components and g the and y -2 ft t nts 1 ft 80 lb 80 lb S S…

A:

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

A:

Q: 2- A rectangular channel with bottom width =8.0m, Manning roughness, n =0.01986, channel bed…

A: The flow area of the given rectangular channel is  The wetted perimeter of the given rectangular…

Q: Make use of Simpson's rule to calculate the work done W by the gas on the face of the piston.

A: The expression for internal of volume is given as ∆V=V2-V1 Substitute the value in above expression…

Q: 2-A water well is fully penetrates a confined aquifer, as shown in the figure, the external radius…

A: Given: A water well that penetrates a confined aquifer as shown below Length of screen = 25 m and…

Q: If you know that the following plotting position formula applies only to data that have an…

A: As given the equation is: 4k+6k=9k Simplifying the equation above to calculate the value of k

Q: 8.13 A polycarbonate sample showed a craze growth length and time relation- ship of e=k log(t/to).…

A: Following is the given relationship between the craze growth length and time of the polycarbonate…

Q: 8.1: Use the virtual work method to determine the horizontal and vertical deflections at joint B of…

A: Due to issue in Math type , providing handwritten solution

Q: Q4: It is required to construct a pile foundation comprised of 25 piles arranged in 5 columns at…

A: Given that Total imposed load= 3000 kN The diameter and length= 50 cm and 12m The water table was…

Q: F10-2. Determine the moment of inertia of the shaded area about thex axis,

A: step 1-

Q: Three concrete cylinders are cast in the field and cured on site. After 3 days they are brought and…

A: Given, Failure load for sample 1 = 212000 N  Failure load for sample 2 = 225000 N

Q: 2. A section of highway has the flow-density relationship as q= 50k-0.156k². What is the capacity of…

A:

Q: Problem 16.1. Determine. · the deflection at point D of the beam shown below. El is By the moment-…

A: Moment Area Method- In this method the area of the bending moment diagrams is use for finding the…

Q: is impure tricalcium silicate is impure (C3S) and dicalcium silicate (C2S). * Tobermorite,…

A:

Q: ex a solid shaft is subjected to a torque of 1-6 kN.m find the necessary diameter of the shaft. if…

A:

Pressure and Stress