Change the following sentences into the negative and the interrogative forms: 1. Salam is a hard-working technician. 2. Alaa and Mazin like chemistry. 3. Sara wears a school uniform. 4. They use computers. 5. He does his homework every night.

Q: How do you convert gpm to ft?

A: A cross-sectional area's flow of fluid is measured in gallons per minute. In simple terms, it…

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen…

A: As per the Guidelines of Bartleby We are supposed to answer only first three subparts. Ultimate…

Q: A. ADJUST THE GIVEN CLOSED COMPASS TRAVERSE LINE LENGTH OBSERVED BEARINGS FORWARD BACKWARD STA…

A:

Q: We found that the Reynolds and Froude numbers Were important? discuss it

A: Reynolds number Froudes number Both numbers are widely used in fluid behaviour study.

Q: How to convert a value from the kips unit to a value in the ib unit

A: Brief concept introduction- Kips and lb are the two major units that are used for the measurement of…

Q: A tube is used as a siphon to discharge an oil of specific gravity 0.8 from a large open vessel into…

A: Since the question comprises of a number of subparts, the solution for first 3 subparts is as…

Q: For laminar flow in a pipe of radius 0.9 m, the point of maximum instability would occur at a…

A: Given data- Radius of the pipe R=0.9 mLaminar flow in the pipeTo Find-Distance of the point of…

Q: If the value of the atmospheric pressure reading using the barometric gauge is (750 mm) and the…

A:

Q: _n-coil with a temperature of 6°C and leaves it -pipes system shown in the figure below.

A: Given:- temperature=6 degree celcius change temperature=12 degree celcius To find:- diameter of all…

Q: Draw the front section, horizontal projection, and side projection MB 42 30 28 14 40 2oma R22. 21 25…

A:

Q: ) To tal density b) dry densiz y =)degree of saturation )saturated densizy (assume no volume change)

A: This question has been taken from geo technical engineering

Q: Rainfall of intensity 20mm/h occurred over a [wa watershed of area 1km2 for duration of six hours.…

A: Given  Rainfall intensity = 20 mm/h  Area of watershed = 1km2 = 106 m2  Duration of rainfall = 6h…

Q: The matter proceeds further. The Arbitral Tribunal meets with the parties at the Preliminary Meeting…

A: Part a Verbieste  requests to amend the pleadings of the claim must not be allowed by the tribunal…

Q: Q5: Determine the resultant couple moment acting on the beam. Solve the problem two ways: (a) sum…

A:

Q: mine the resultant couple e into x and y components and g the and y -2 ft t nts 1 ft 80 lb 80 lb S S…

A:

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

A:

Q: For the composite structure shown in Figure (3), use the unit load method (virtual work method) to…

A:

Q: A soil yielded a maximum dry unit weight of 18 kN/m3 at a moisture content of 16% during a Standard…

A: Given, G = 2.65 Moisture content, w= 16% Dry unit weight = Yd = 18kN/m³ Degree of saturation = ?

Q: Example 2.5 An oven dry soil sample of volume 250 cc weighs 430 g. If the specific gravity of solids…

A:

Q: 6. In a pipe of 200 mm diameter the maximum velocity of flow is found to be 1.5 m/s. If flow in the…

A: Diameter of pipe = 200mm  Radius of pipe = 100mm or 0.1m MAximum velocity of flow (Vmax) = 1.5m/s To…

Q: 8.1: Use the virtual work method to determine the horizontal and vertical deflections at joint B of…

A: Due to issue in Math type , providing handwritten solution

Q: The regression analysis of a 30 year flood data at a point • on a river yielded sample mean =…

A:

Q: 82 A solid steel shaft of 60mm diameter is to be replaced by a hollow steel shaft of the same…

A:

Q: ex a solid shaft is subjected to a torque of 1-6 kN.m find the necessary diameter of the shaft. if…

A:

Q: رشت متار فيامین( (2 Forthe beam shown, a. draw sFD and BMD, b. prove that for the isosceles:, Tnax.…

A: As per company's guidelines we can only answer first three questions.  Kindly post other questions…

Q: Question 3: Is it possible to fit a cation Ct of radius 180 pm in the tetrahedral site of the…

A:

Q: :Compute the volume using the prismoidal formula and by average end areas for the following…

A: h = 5.3 ft, h1 = 7.4 ft , h2 = 7.8 ft, b = 24 ft, b1 = 23 ft , b2 = 23.7 ft Let A1 = Area of station…

Q: 5- What are the main advantages and disadvantages of turbulent flow? 6- Increasing the flow velocity…

A: Disadvantages of turbulent flow  Turbulent flow is unstable  Velocity and pressure changes rapidly…

Q: A cantilever retaining wall is required to support a backfill having the following soil properties:…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Q5/ Find job mix formula by using mathematical method. Aggregate Specification Sieve Size A B C…

A:

Q: The pressure head at level AA is 0.091 m of water, and the unit weights of gas and air are 5.50 and…

A: given data water head at AA=0.091m unit weight of air=12.35N/m3 unit weight of gas=5.5N/m3

Q: . The model has to maintain (A. Geometric, B. Dynamic, C. kinematic, D. Kentics, E. All of them, or…

A: 1.) F- A to C 2) E - All of them  3)D

Q: In the overhanging beam show, determine P so that the moment over each support equals the moment at…

A: Determine P so that the moment over each support equals the moment at the midspan.

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.