Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot astress-strain curveHomework-helpTable 3-2 The results of a tensile test of a 0.505 in. diameter aluminum alloy test bar, initial length (1o) = 2 in.CalculatedLTOLoad (Ib)Change in Length (in.)Stress (psi)Strain (in./in.)0.00010000.0010.00054,99314,97824,96334,94837,44539,44239,94139,69137,94430000.0030.001550000.0050.002570000.0070.003575000.0300.015079000.0800.04008000 (maximum load)0.1200.060079500.1600.08007600 (fracture)0.2050.1025

Answered: Example: Convert the change in length…

Engineering

Mechanical Engineering

Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a stress-strain curve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can you please find Normal Stress, tangential Stress and Resultant Stress
Correctly complete the following phrase below: "When a structure is subjected to general loading in two dimensions, Tresca and the Von-Mises criteria are used to... determine the maximum shear stress." Don't Know calculate the principle planes." calculate the deformation in a structure." determine failure of materials that behave plastically."
For the previous problem, compute the following six stress quantities: Ox, Oy, 0z, Txy, Tyz, Tzx. Assume this is an aluminum alloy (E = 10,000 ksi, G = 3800 ksi, v = 0.33). Do not forget units!
In lab tests on a brick whose dimension are shown in the figure to the right, a force of 1500 N directed at 9.00° above the horizontal is applied on both the lower and upper faces of the brick causing the vertical side of the brick to deform through an angle of 1.25º. (a) How much shear stress is applied on the upper and bottom surfaces of brick? (b) What is the shear modulus of the brick? 9.00° 10 сm 25 cm 3-dimensional view 25 cm Front view after Before applying stress applying stress 10 cm 1.25°
Please answer for that now
Draw the stress-strain diagram for a steel specimen (a ductile material) showing both the conventional and true stress-strain curves. Label all aspects of the diagram. Define the following regions in the above diagram: elastic behavior, yielding, strain hardening, and necking. What are the characteristic stress limits? Locate and define them on the curves.
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience
A fatigue test was conducted in which the mean stress was 70 MPa (10150 psi), and the stress amplitude was 230 MPa (33360 psi). (a) Compute the maximum stress level. i (b) Compute the minimum stress level. i (c) Compute the stress ratio. i MPa i MPa (d) Compute the magnitude of the stress range. MPa
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
Define the term Stresses on Arbitrary Plane?
Consider a metal rod with a critical resolved shear stress of 40 MPa for a specific crystallographic plane (hkl). The angle between the normal to the plane and the applied force is 30 degrees, and the angle between the slip direction and the force is 15 degrees. Two force levels of F1 = 75 N and F2 = 40 N is applied. The cross-sectional area of the rod is 1 mm^(2). Will the slip initiate at the two force levels? Select one: a. F1: Yes, F2: No b. F1: No, F2: No OC. F1: Yes, F2: Yes Od. F1: No, F2: Yes
Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted on a high-strength steel. The test specimen had a diameter of 0.505 inch and a gage length of 2.00 inch. Using software. plot the Stress-Strain Diagram for this steel and determine its: A= TTdT(050s A %3D 1. Proportional Limit, 2. Modulus of Elasticity, 3. Yield Strength (SY) at 0.2% Offset, 4. Ultimate Strength (Su), 5. Percent Elongation in 2.00 inch, 6. Percent Reduction in Area, 7. Present the results (for Steps 1-6) in a highly organized table. e Altac ie sheet (as problelle 4 A = 0.2.002 BEOINNING of the effort Elongation (in) Elongation (In) Load Load #: #3 (Ib) (Ib) 1 0.0170 15 12,300 0.0004 1,500 16 12,200 0.0200 0.0010 3. 3,100 17 12,000 0.0275 0.0016 4,700 18 13,000 0.0335 5. 6,300 0.0022 19 15,000 0.0400 0.0026 6. 8,000 20 16,200 0.055 0.0032 9,500 21 17,500 0.0680 0.0035 8. 11,000 22 18,800 0.1080 0.0041 11,800 23 19,600 0.1515 0.0051 24 20,100 0.2010 10 12,300 0.0071 25…