EXAMPLE:- Consider a spherical container of inner radius ₁ = 8 cm, outer radius ₂ =10 cm, and thermal conductivity k=45 W/m °C, as shown. The inner and outer surfaces of the container are maintained at constant temperatures of T₁ = 200°C and T₂ = 80°C, respectively, as a result of some chemical reactions occurring inside. Obtain a general relation for the temperature distribution inside the shell under steady conditions, and determine the rate of heat loss from the container. . 2

EXAMPLE:- Consider a spherical container of inner radius ₁ = 8 cm, outer radius ₂ =10 cm, and thermal conductivity k=45 W/m °C, as shown. The inner and outer surfaces of the container are maintained at constant temperatures of T₁ = 200°C and T₂ = 80°C, respectively, as a result of some chemical reactions occurring inside. Obtain a general relation for the temperature distribution inside the shell under steady conditions, and determine the rate of heat loss from the container. . 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
Answer this ASAP,thx An empty sphere is made of aluminum (k = 202 W/m. °C) with an inner diameter of 4 cm and an outer diameter of 8 cm. The inside temperature is 100°C and If the ball above is coated with an insulating material having k = 50 mW/m. °C 1 cm thick. The outside of this insulation is in contact with an environment having h = 20 W/m.°C and Ts = 10°C, calculate the heat transfer under these conditions.
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. (10 Pts)
Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
A furnace wall consists of 2 ft of brick . The brick has athermal conductivity of 0.6 Btu/ hr sq ft ( ° F /ft), a specific heat of0.2 Btu/ lb ° F, and a density of 110 lb/cu ft. The temperature atthe inside surface of the wall is 1100 ° F , and at the outside surface,200 ° F .(a) Calculate the thermal diffusivity of the brick .(b) Calculate the heat loss per hour through a wall 10 ft high and10 ft long(c ) Calculate
During daytime, the outside air temperature is measured at Ta = 35 °C. A house with an inside temperature of Tin = 20 °C is separated from the outside by a brick wall as shown in Figure 1. i Briefly discuss what will happen in terms of heat transfer process and the mode of heat transfer involved. ii. Identify the parameters that affect the rate of heat transfer in this case T. = T = 35°C 20°C Brick wall
EXAMPLE = wire Consider a long resistance wire of radius ₁ 0.2 cm and thermal conductivity k = 15 W/m . °C in which heat is generated uniformly as a result of resistance heating at a constant rate of g = 50 W/cm3. The wire is embedded in a 0.5-cm-thick layer of ceramic whose thermal conductivity is k = 1.2 W/m °C. If the outer surface temperature of the ceramic layer is measured to be Ts = 45°C, determine the temperatures at the center of the resistance wire and the interface of the wire and the ceramic layer under steady conditions. ceramic 17 Interface Mech. Eng. UOK Wire Ceramic layer T₁=45°C ۳۰/۱۰/۲۰۱۳
Consider the following cases: Case 1: A rod with specified surface temperature. Case 2: A rod with specified surface temperature with heat generation. Case 3: A rod with specified surface temperature with variable thermal conductivity k=k(1+BT), ß: is constant. The quadratic temperature profile T(r)= f(r) will be in:
A cylindrical pipe is made up of two materials. The inner material A, which has thermal conductivity of ka, has inner radius ra and outer radius re. On the other hand, the outer material B, which has thermal conductivity of kb, has inner radius re and outer radius rb. Contact resistance between the two materials is known to be hc. The temperature at the inner radius of material A (at ra) is Ta, while the temperature at the outer radius of material B (at ri) is T3. Find an expression for the temperature at the inner radius of material B (at r.) in terms of the given variables.
asap
Consider a homogeneous spherical piece of radioactive material of radius r0 = 5 cm that is generating heat at a constant rate of q.= 3.8x107 W/m3 The heat generated is dissipated to the environment T∞= 27°C and h = 110 W/m2°C steadily. The outer surface of the sphere is maintained at a uniform temperature (Ts) and the thermal conductivity of the sphere is k = 25 W/m°C. Assuming steady one-dimensional heat transfer, (a) express the differential equation and the boundary conditions for heat conduction through the sphere, (b) obtain a relation for the variation of temperature in the sphere by solving the differential equation, and (c) determine the temperature at the center of the sphere
The temperature distribution in a wall (conductivity k=6-W/m2C, thickness L=10-cm) is given as T(x)=(-454 x2+53 x+ 17) (in °C) Assuming unit wall surface area, calculate the rate of heat loss from both sides of the wall in Watt.