Example: An HMA sample had been taken from a road during the construction, the weight ofsample after the separation of binder was 4621 gm and the retaining on each sieve is shown infollowing table. Determine whether HMA sample is satisfying the Iraqi specification for basecourse asphalt or not?[ 62 ]Dr. Basim Al-HumeidawiUniversity of Al-QadissiyahRoads and Transport DepartmentCollege of EngineeringTechnology of asphalt concrete2nd Year% passing according to Iraqi specificationBaseBinderSurfaceSurfacecoursecourse Acourse Bcourse37.51002590 - 10010086.321963276 - 9090 - 10010013.6712.592056 - 8070 - 9090 - 1001009.561248 - 7456 - 8076 - 9090 -1004.7562829 - 5935 - 6544 - 7455 - 852.3640519 - 4523 - 4928 - 5832 - 670.38335 -17'5 - 19'5 - 21'7- 23 '0.0754062 -8'3 - 9'4 - 10'4 - 10'Pan185Total4621weight

Answered: Image /qna-images/answer/b84feb37-46fc-46bd-92cb-41f63be302da.jpg

Example: An HMA sample had been taken from a road during the construction, the weight of sample after the separation of binder was 4621 gm and the retaining on each sieve is shown in following table. Determine whether HMA sample is satisfying the Iraqi specification for base course asphalt or not? ( 62 ] Dr. Basim Al-Humeidawi

Example: An HMA sample had been taken from a road during the construction, the weight of sample after the separation of binder was 4621 gm and the retaining on each sieve is shown in following table. Determine whether HMA sample is satisfying the Iraqi specification for base course asphalt or not? ( 62 ] Dr. Basim Al-Humeidawi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Table shows the grain size distribution for two aggregates and the specification limits for an asphalt concrete. Determine the blend proportion requiredto meet the specification and the gradations of the blend. On a semilog gradation graph, plot the gradations of aggregate A, aggregate B, the selected blend,and the specification limits.c
Problem No. 1A flexible pavement for an urban interstate highway is to be designed using the AASHTOmethod to carry a design ESAL of 3 x 106. It is estimated that it takes about a week for water tobe drained from within the pavement and the pavement structure will be exposed to moisturelevels approaching saturation for 30% of the time. The following additional information is available: Elastic modulus of asphalt concrete = 450,000 psiResilient modulus of base material = 35,000 psiResilient modulus of subbase material = 15,000 psiCBR of subgrade material = 8(a) Consider designing the same pavement with only asphalt concrete and base layer (excluding subbase layer). Use the information provided in Problem 1. (b) Compare strengths and weaknesses of each design.
An asphalt binder is intended to be used in a climate with maximum 7-day pavement temperature of 73 •C and minimum pavement temperature of -18•C. Following is the SHRP tests results on the asphalt binder. This asphalt meet the requirements for original binder, _meet the requirements for RTFO aging and meet the requirements for PAV aging Original Binder DSR at 76 °C: G*=0.96 kPa, ô=65• RTFO Aged Binder Mass lost: 0.55 % DSR at 76 °C :G*=1.72 kPa, ô=54• PAV Aged Binder DSR at 31 •C : G*=8520 kPa, ô=37• BBR at -12 °C and 60 sec : Stiffness = 289 MPa , m-value = 0.281 DTT at -12 C : 2.2% does not, does not, does no does not, does, does not does not, does, does does, does, does not
Explain why asphalt concrete samples from the hot-mix plant are taken for compaction in the laboratory during asphalt overlay construction
QUESTION 1 A drum mix asphalt plant is different than a batch mix asphalt plant. O True O False QUESTION 2 Excess asphalt mix is kept in a grain silo until trucks transport it to the job site. O True O False QUESTION 3 Typically, ODOT calls for minimum 7" layer of surface asphalt mix to be placed and then a 4" layer of aggregate base beneath. O True O False
BMD revolves around the concept of balancing rutting and cracking of the mix. The figure below applies to all three different BMD methodologies. Using your own words explain all different components of this figure, how BMD is achieved, and what different tests and parameters are used to assess the asphalt mixes cracking and rutting performance. Submit your solution in a word file (maximum number of words allowed: 800) Cracking Durable Min Max Rinder Content Stable Rutting
Problem #1 The following figure shows the results from the dynamic modulus test for asphalt mixtures. The specimen is 4" in diameter and 6" in height. The gauge length for the axial LVDT is 4". Time lag is 0.25s. Find |E*I, and phase angle . Axial force(lbf) 65 60 40 20 0 -20 -40 -65 0 Dynamic modulus test result (gauge length = 4") 0.5 Time (second) 1 0.0010 0.0009 0.0006 0.0003 0 force (lbf) disp (in.) -0.0003 -0.0006 -0.0009 -0.0010 1.5 Axial displacement(in) 4"
Flexible road pavement is more popular as compared to concrete road pavement in Malaysia. i) Discuss why flexible road pavement is more popular. ii) Describe one (1) test that is used to measure hardness of bituminous material