EXAMPLE: A single-phase, full-wave center-tapped rectifier supplies power to a 1-k2 load. The ac voltage applied to the diode is 600 V rms. If the diode resistance is 25 N and that of the transformer secondary is negligible. Determine (a) average load current (b) average value of load voltage Note: The rms value of the ac voltage across each secondary half is 300 V.

EXAMPLE: A single-phase, full-wave center-tapped rectifier supplies power to a 1-k2 load. The ac voltage applied to the diode is 600 V rms. If the diode resistance is 25 N and that of the transformer secondary is negligible. Determine (a) average load current (b) average value of load voltage Note: The rms value of the ac voltage across each secondary half is 300 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
For the circuit shown in Figure, consider Ideal diodes. If Vs = 19sin wt, Vb = 4 V, the minimum value of output voltage is: Vout at of estion Vs Vb Oa. -4 V Ob. -15 V Oc. -19 V Od. 4 V
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the peak signal voltage received by the diode
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
H.W: - For a single phase half wave uncontrolled rectifier if the input supply voltage is (v,= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings: - i. Draw the rectifier circuit. ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. iv. If the load is (R=102), then determine the mean and rms values of the current.
Question 2) A full-wave rectifier with ohmic load given in the figure below feeds a 75 Q load and the effective (rms) value of the source voltage is 220V, its frequency is 50 Hz. Accordingly, find the following desired circuit parameters: a) the peak voltage of the source, b) the peak current of the load, c) Average stress of the load, d) Average current of the load, e) The effective (rms) voltage of the load, f) Effective (rms) current of the load, g) Power of the load i D2 vs R
In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 20N and load resistance is 1.5K. Calculate, i. Im ii. Ide
Three phase diode rectifier connected to 400V, 50 Hz source is feeding a resistive load of 100 with High 3 inductance. The distortion factor given to be . What π will be the power drawn at fundamental frequency from mains. (A) 5.2 kW (C) 27.9 kW (B) 16.8 kW (D) 48.1 kW
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center tap to each end of the secondary is 70 V and load resistance is 1000 0. Find: a) The mean load voltage and current b) The r.m.s. value of load current e) The PIV of the diode d) The efficiency of rectification
Base from the values given. Fill in the questions.