Example 7.6 For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spacing of truss = 3.0 m centre to centre Inclination of roof 30° Spacing of purlins = 2.0 m centre to centre Wind pressure = 1.5 kN/m2 Roof coverage -A.C. sheets weighing 200 N/m2 %3D %3D %3D %3D Design: (i) angle section purlins.00 00brol beob IstoT

Example 7.6 For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spacing of truss = 3.0 m centre to centre Inclination of roof 30° Spacing of purlins = 2.0 m centre to centre Wind pressure = 1.5 kN/m2 Roof coverage -A.C. sheets weighing 200 N/m2 %3D %3D %3D %3D Design: (i) angle section purlins.00 00brol beob IstoT

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

11.ASAP
p=67
(i) Find the shape factor for the tee section as shown in figure. 20 mm 20 mm 120 mm- 200 mm
Figure 3 shows a truss where P = 40 kN and Q = 27 kN. The force reaction at A in the y-direction is FAy = 29 kN up and the force reaction at G in the y- direction is FGy = 38 KN up. In the question that folows, select ihe anawer that in choneat to the tre vale. What is the magnitude of the force in member KL in units of kN? O 38.7 O 58.7 52.0 453
2.3 A monolithic floor framing plan is shown in the figure. The columns are 300 mm square, girders are 250mm wide by 450 mm deep and slabs are 100 mm thick. The floor loads include floor finish of 0.77 kPa, ceiling system of 0.25 kPa, partition load of 1.0 kPa and live load of 4.8 kPa. Bar centroid from the edge of the beam is 70mm. Calcualte: Maximum ultimate bending moment at discontinuous end of girder GH to the nearest whole number = ___?_____ kN·m
answer A only . Answer just by virtual work method
Hi, can somebody able to answer this one? pls. i really need it. thank you.
my answer is wrong please help me solve
The beam is loaded as shown. which of the following nearly gives the flexural stress due to tension in MPa? 240 mm W = 12 KN/m 60 mm 200 mm 4 m 4 m 4 m 60 mm 202.967 none among the choices 165.856 105.802 OO O O
a w12x65 column section shown in the figure is pined at each end and has an additional support in the weak direction at a point 4.19m from the top. Use x = 4.71 K=1 A = 12323 rx = 134.11 ry = 76.71 Fy = 248 Determine the a) design compresive strength (KN) b.) Elastic critical buckling stress (MPa) c.) Flexural buckling stress D.) Critical slenderness ratio E.) Nominal compressive stress F.) allowable compressive strength
Please show your solution on a paper with FBD
two span beam subjected to shear and flexure only is reinforced as follows: Section @ midspan @ face supports Top bars 2-20mm 5-20mm Bottom bars 3-20mm 2-20mm Given Stirrup diameter: 10 mm concrete fc = 21 mpa steel rebar fy = 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in single layer calculate the following: a) tensile steel ratio in positive bending moment at midspan (round off to 5 decimals) b) design moment strength of section at midspan for positive bending ( in kN•m , nearest whole number) c) nominal design strength of section at face of support for negative bending ( in kN•m , nearest whole number)