Example 5Calculate the live load of a R.C.C. slabSize of the Slab is 3.0mt by 5.0 mt., Thickness is 12 cm.Calculate the live load on slab for school building.lengthwidthAreaLive load forresidential buildingLive load5.0 MT3.0 MT.5.0 X 3.0300 kg/ SMT15 X 30015 SMT4500 kg

Following are the given information. Type of building = School Length of slab, L=5.0 m Width of…

Answered: Example 5 Calculate the live load of a…

Example 5 Calculate the live load of a R.C.C. slab Size of the Slab is 3.0mt by 5.0 mt., Thickness is 12 cm. Calculate the live load on slab for school building.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A reinforced concrete column 256 mm in diameter is designed to carry an axial compressive load of…

Q: 3. An 8"diameter timber pole is fixed into a large concrete footing at grade and is completely pin…

Q: M _c s' s' Eps_s b_w Click to see additional instructions For C40 and S500, solve the given section…

A: Solution; Given Data; bw=300 mmh=500 mmd=h-25-10-202=455 mmd'=25+10+202=45 mmAs=4-φ20=4*314=1256…

Q: A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that…

Q: Topic: FLAT SLAB Determine the total dead load (in kPa) of the following different types of slab if…

Q: A concrete column 4.00 m high with a cross sectional dimension of 30 cm x 30 cm is resting on a…

A: Introduction- A steel and concrete column is a structural part made of concrete with an integrated…

Q: 4. The development length of a deformed reinforcement bar can be expressed as φσ, (0) From the bd…

A: Deformed reinforced bar- Development length Ld=1kϕσs4τbd Value of k=?

Q: 1. Find the volume of concrete needed to fill the slump cone for the test. 2. Find the volume of…

A: Given Slump cone diagram with dimensions and thickness. To Determine 1. Find the volume of concrete…

Q: Problem 2: Provide reasons for why development length must be satisfied in structural concrete

A: development length is the additional length extended or projected to attain desired bond strength.

Q: Q3: For the small building which is covered by a slab 20 cm thick as Shown. Concrete Blocks are…

A: RCC structure R.C.C. Structure Design: a structure made up of a single piece of concrete and steel…

Q: A floor panel 3 4 m wide and 12 m long is intended for a vibratory machine in a factory. The…

Q: Topic: HOLLOW BLOCK SLAB Determine the total dead load (in kPa) of the following different types of…

A: We have to determine the value of total dead load:-

Q: Use 26 liter: Which of the following gives the required volume of gravel?

Q: Determine

A: The minimum area if shrinkage bars is given by 0.12% of gross area of slab.

Q: List four ways knowledge in metallurgy can be used in road construction. Do not explain but add…

A: Metallurgy is the field of material science and engineering which studies and focuses on the…

Q: What is the amount of load that center of the rectangular concret To ic 3 5ON

A: Modulus of ruptutr is given by :M=3PL2bd2

Q: A normal-weight concrete test beam 150mm by 150mm in cross section and supported on a simple span of…

A: Given: The cross-section of the beam is 150 mm x 150 mm. The length of the beam is 600 mm. The load…

Q: Refer to Figure 3.7 Segments 1 and 2. What would be the approximate slab thickness if the mean…

A: K= 72 pci Ec =5×106 psi s'c = 750 kips J=3.2 S0 =0.29 R=95% ZR =1.645 ∆Psi= 4.2-2.5…

Q: A 120 thick one-way RC slab is subjected to loads (wt. of slab is not included) as shown. Required:…

A: Given Data : Thickness of one-way RC slab (t) = 120 mm live load= 2.2 kPa Dead load=5.1 KPa fy=411…

Q: Define Hollow-Core Slab Production.

A: Pre-stressed concrete: The prestressed member is a structural element. It used in high stability…

Q: A square column with side dimension of 50 mm rests on top of a timber footing. It is determined that…

Q: A reinforced concrete column 200mm in diameter was designed to accommodate an axial load of 350 kN.…

Q: What is the moment at the midspan of a one-way floor system to carry a service live load of 12 kPa?…

Q: Select the magnitude of the self-weight of a lightened slab if the module has 145,000 cm3 of…

A: Asked: To determine the self weight of the lightened concrete slab. Given: Volume concrete =…

Q: The compression gravity loads for a building slab have been estimated with a superimposed dead doads…

A: Answer (a) We are given Superimposed Dead Load = 4.76 kpa Live Load = 1.9 kpa We know that the…

Q: Question #1 why is the sum of un-factored loads instead of sum of sum of the factored loads used for…

Q: one-way slab to support a load

A: To design the slab for the given specifications

Q: A column load (force) of 33 kip acts on a square footing. Calculate the size of the footing if the…

A: Given data,square footingcolumn load=33 kippressure on soil=1 kip/ft2depth of aggregate is 8…

Q: Q2: The following data represent the compressive strength of 50 bricks, determine: 1) the mean (2)…

A: From above given data we consider : Number of samples = n Compressive strength(kN) = x

Q: A short plain concrete column with dimensions of 0.3 * 0.3 * 0.9 m is to be constructed. If the…

A: gdgggj

Q: 1. Find the volume of concrete needed to fill the slump cone for the test. 2. Find the volume of…

Q: Why the procedure to analyze the effects of secondary compression in a soil layer subject to usual…

A: Secondary compression or 2o consolidation:

Q: A. Design two-way slab as shown below to carry the live load 300 kN/m2fc' = 24 MPa kg/cm2, fy =…

Q: Suspended and non-suspended slab can both be designed as flooring system in building structure. List…

A: Suspended slabs are slabs that are not in direct contact with the ground. They form roofs or floors…

Q: From the following figures, find the following materials required for its constructions. a. 15 x 20…

A: Calculating the sand, cement for plastering total area=2A Considering all the dimensions of the…

Q: Problem Solving You are to design the concrete mix proportion for concrete foundations (single…

Q: The two-way slab shown in the following Figure has been assumed to have a thickness of 6.5 in.…

A: Solution; (Using the same concrete for Beams and Slabs)

Q: A reinforced concrete square column measuring 16in on its sides is 5m long. Estimate the quantity of…

Q: What is the moment at the midspan of a one-way floor system to carry a service live le of 22 kPa?…

Q: A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that…

Q: Discuss the suitability of different types of column supported by RC slab

A: Introduction : Column is a vertical member whose effective length is greater than 3 times to its…

Q: A 4x6m concrete slab has a uniform thickness of 125mm. Find the quantity of 50kg cement, sand, and…

Q: What is the moment at the midspan of a one-way floor system to carry a service live load of 12 kPa?…

A: Given, Live load=12 kPal=5 munit weight of concrete = 23.60 kN/m3

Q: 4.7 The cross section of a conventionally reinforced concrete one-way slab is shown below. Using ACI…

A: Minimum thickness of slab

Question

Example 5
Calculate the live load of a R.C.C. slab
Size of the Slab is 3.0mt by 5.0 mt., Thickness is 12 cm.
Calculate the live load on slab for school building.
length
width
Area
Live load for
residential building
Live load
5.0 MT
3.0 MT.
5.0 X 3.0
300 kg/ SMT
15 X 300
15 SMT
4500 kg

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Discuss the process of loading and load leveling and explain what quantitative technique are available to help in this process
Problem #2: Design a (One Way Slab) slab whose clear length is 20 ft x 12 ft which is subjected to a live distributed load of 150 psf.
Note: kindly give me both right solutions according to the question.
question is attached, thank you!
TABLE 1.2 Minimum Densities for Design Loads from Materials Aluminum Concrete, cinder Concrete, stone Clay, dry Clay, damp Sand and gravel, dry loose Sand and gravel, wet Masonry, lightweight concrete Masonry, normal weight units Steel, cold-drawn Wood, Douglas Fir Wood, Southern Pine Wood, spruce AN/w 27 120 22.6 123 15.7 18.9 165 21.2 5.7 723 5.3 5.8 45 TABLE 1.3 Minimum Design Dead Loads From Paris and Walls Wood 1x plated Woodplatered Woodst 51x32mm, platered Cindere per Lightweight complaine Ceilings Aucuntic Shond Spendedahand Angle 5.54 9.57 2017 005 8:24 0.41 904 TABLE 1.4 Minimum Live Loade Oorspany or Use Amely Fixed seats and at Garage (can only) Officeday Lebbin Love Load 4.79 192 4.79 VEST S Occupancy or Use Dwelings (one-and two-mily) Hotels and many bo Private and don Campos Fint Coor comidon Comidon abfint floor Live Lead KN/² 190 4.39 3.33
please answer asap thank u
A light-weight concrete was cast-in-place to form a rectangular beam. If its unit weight is 17.24 kN/m3, and its compressive strength is 27 MPa, determine its Modulus of Elasticity in MPa. Round-off only on your final answer, in three-decimal places. need it asap pls
A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that the column carries an axial load of 621 kN. If the punching strength of concrete is 17.40 MPa, determine the minimum thickness (mm) of the footing.
If the elastic sag of the concrete member was 3 cm for the corresponding continuous load, what is the final total sag in consideration of additional long-term sag due to creep and dry contraction? (However, the load loading period is 10 years, and the compression reinforcement ratio p′=0.005)
Answer the following questions: 1. Formworks for floor slab with 3,500psi to be removed after 14 days with strength 1800 psi, would you allow it or now? 2. If you are to pour 115 cu.m for your all of columns along Grid A, how many samples should you submit for testing and what samples? 3. You have 850 cu.m of soil embankment material, how many samples should you submit for MDR and CBR test ONLY? 4. You have 750 cu.m of soil embankment materials, how many samples for all 3 set of tests? Reference: DPWH Standard Specifications for Public Works and Highway (2004 edition), Volume II
Analyze & design one way and two way slab systems.
What is the moment at the midspan of a one-way floor system to carry a service live load of 12 kPa? The slab has a length of 5 m with both ends continuous. Use the unit weight of concrete of 23.60 kN/m3. Round up slab thickness by multiples of 5 mm. Round off your final answer in 3 decimal places.