Example 3: Design a trapezoidal channel of water having a velocity 0.6 m/s, channel side slope 1:1.5, flow rate 3 m3/s, c=65, hydraulic radius 10 m? Top width=b+2ny- y 1+"M

Q: Determine the critical depth (m) for following rectangular open channel: Flowrate = 64 m^3/s Channel…

A: Given that: A rectangular channel, with flow rate, Q=64 m3/sChannel width, B=6m

Q: A rectangular concrete channel (n = 0.015) is 10.5 ft wide, has a slope of 0.006, and a discharge…

A: Given data in question Width 10.5 ftDischarge 200 cfsSlope 0.006Depth 5.7 ftN = 0.015To find out…

Q: 3. Two adjacent communities are represented by the simplified system shown below. Determine the…

A: 1: Head Loss CalculationsWater Density (ρ): 1000 kg/m³Acceleration due to Gravity (g): 9.81…

Q: emperature when this system was assembled was 74F, what would be the stress in a temperature of 4OF?…

A: According to given data  The assembly below will be used for each problem Lengths, diameters, and…

Q: O A rectangular channel 1.30 wide carries 1.10 m/s of water at a depth of 0.85 m. If a 30-cm wide…

A: Equating specific energy of channel at both section to get elevation of water surface

Q: For #5-7, assume there is a creek with a width of 4.6 m, depth of 23 cm, slope of 0.001 m/m, and…

A: Given: DischargeQ=0.13 m3s Width of rectangular channelB=4.6 m=460 cm Depth of flowy=23 cm…

Q: b) Using the conditions of best hydraulic trapezoidal section, design a rigid-boundary trapezoidal…

A:

Q: Q (5-2)/ Water flows uniformly in an earth rectangular cross section open channel. Data available…

A:

Q: Fluid Mechanics question: Water flow from a pone through a 10cm diameter pipe. Find the flow rate…

A: Given: Elevation of point ‘A’ from ‘B’ = 10               Diameter of the pipe = 10cm

Q: please help with hydrology problem. make sure it is correct, will thumbs up if correct.

A: Approach to solving the question: through determining whether the flow in the triangular channel is…

Q: I need help on this problem Manning equation problem for parts a, especially rearranging the…

A: R (hydraulic radius) = A(area)/P(perimeter) = 250*20/(250 + 2*20) = 17.24 Q = 25000 ft3/s Q = 1/n x…

Q: Find the downstream water depth y2 and velocity V2 for a rectangular channel with constant width (5…

A:

Q: asap pls

A: Given: Discharge (Q) = 1 cm = 0.01 m3/s   Bed slope (S) = 0.0021 To solve this, we use Manning's…

Q: Find the value of discahrge through pipe having cross sectional area 2.2 m2 and flow velocity is 2…

A: Given data,  Cross Sectional area (A) = 2.2 m² Flow velocity (V) = 2 m/s

Q: hydraulics *use handwritten    A rectangular channel 5.50 m wide and 1.30 m deep is laid on a…

A:

Q: Water flows in a rectangular channel at a depth of 20 cm and with downstream depth after the…

A:

Q: 7. Water flows in a 3m wide rectangular channel. If the critical depth was measured to be 0.542m,…

A: Given data- Width of the rectangular channel- W=3 m, Critical depth y=0.542 m, To Find- The maximum…

Q: Plz, solve the two parts of this question. Hydraulics. Reg.No: 5395 Question. a). A…

A:

Q: A rectangular, unfinished 33-ft-wide concrete channel is laid on a slope of 8 ft/mi. (a) Determine…

A: Given, a rectangular channel width,w =33 ft slope,s=8 ft/mi flow rate,Q= 400 ft3/s we have to…

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.