Example (2): Resolve the 200 N force shown acting on the pin Into components In the (a) X and Y directions, and (b) x' and Y directions.

Q: Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a. Force F1…

A: Given:F1=2170 NF2=1240 NR=3100 N

Q: Examples Example (1) : The screw eye in Figure is subjected to two forces, F, and F,. Determine the…

A:

Q: Part A If FA = 40 kN and FB = 40 kN , determine the magnitude of the resultant force(Figure 1).…

A:

Q: Example 1- determining the components of the specified forces in the direction of the x and y axes…

A: Draw the free body diagram of the force system.

Q: 3-5. Calculate the moment about point A in Figure P3-5. 800 lb A 4 5' 3 FIGURE P3-5 200 lb 4 | 7' 3'…

A: Moment about a point is the product of force and the perpendicular distance between the line of…

Q: the direction of the force (f) is 30° find the horizontal component if the vertical component is…

A: Given the direction of force is 30° Vertical component of force is Fsin(theta) F sin (theta) = 30  F…

Q: g x direction. The initial strain along y direction. The initial strain in z direction Additional…

A: Rectangular steel block  Lx = 3 inchLy = 2 inchLz = 4 inch Fx = + 30 kipsFy = -60 kipsFz = 54 kips

Q: Compute the moment arm for the force in cable C, measured relative to the AB axis. Use d₁ = 3.5 ft,…

A:

Q: 1. You are tasked to design a shaft for power transmission through a belt and pully at its right…

A: Given:To find:

Q: A proper free-body diagram for a fixed support in two-dimensional analysis has: O A force in the x…

A: identify the reaction at fixed support in 2 - D.

Q: the bracket must support the four forces shown in figure. the magnitude of the resultant force is: F…

A:

Q: Q.1 Determine a pair of horizontal and vertical components for the force shown in Figure (1). 225 N…

A:

Q: Q1: In Fig. (1) replace the force 200 N acting on point D with a force at point E acting vertically…

A:

Q: (a) Based on Figure 4(a), explain in your own words and sketches, suggest several methods to remove…

A: Moment about cg will be zero.  This will give an expression for maximum force at A in terms of alpha…

Q: 1. Determine the component of each force along the specified x - y axes. Refer figu 1. the exclusive…

A:

Q: Determine the magnitude and sense of the forces in bars A and B in the figure shown below. Show all…

A: Given data, A 80 k downward force is acting in a junction of bar A and B. To determine:- The…

Q: Problem 3 Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on…

A:

Q: determine the x and y components of 200 n force withe angle=330° as shown in the figure ?

A:

Q: L,=40mm; L,= 120mm; L,=80mm L=100mm and 0,=65°. Find the possible value of 0, and and 0,

A:

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: A 10.5 ft B 200 lb 2 ft 2 ft 1 ft 1 ft 1 ft, F

A: Given: The value of the weight is 200 lb.

Q: A 2 ft F, 4 ft M B. - 3 ft- 30 -x F,

A: Given that, F1=150 lb,F2=50 lbM=500 lb.ft Consider the given frame, Resolve the given force in two…

Q: Part A If F 191 lb, determine the resultant couple moment. Express your answer to three significant…

A: Given:Force acting, F=191 lbTo determine the resultant couple.

Q: 5. Determine the principal stresses acting at point E by constructing Mohr's circle y. 150 mm 200 mm…

A:

Q: Second moment of area The second moment of area employed in the equation to calculate maximum shear…

A: Given : The shear force in this section is The diagram is,

Q: nd of the point A of the bracket in Figure 1b, is subjected to three  concurrent and coplanar forces…

A: To determine the resultant and the orientation of the resultant.

Q: Determine force in members: CD, KJ

A:

Q: The spinning wheel, as shown in the figure, is subjected to a load of 200 lb. F calculate the…

A: Given: The load, W = 200 lb

Q: Figure 1 (a) shows an anchor bolt which is loaded by two forces Pand Q that have magnitudes of 10 kN…

A:

Q: 1. Given Figure 4 determine the force in member AD in kN 2. Given Figure 4 determine the force in…

A: Answer: (1) The force in member AD is 320 kN (Compression). (2) The force in member AB is 357.8 kN…

Q: Detemine the resultant force at A. for the figure below Hint : 1- Find the position of all points…

A:

Q: The rigid bars ABC and CD are supported by pins at A and D and by a steel ro at B. There is a roller…

A: