Example 2: In order to tighten the bolt shown in the figure below, a force F is applied to the end of the curved wrench, Find: 1) The magnitude of the force F that produces a clockwise moment about the bolt center B of 40 N.m (take 0 = 25°), 2) The magnitude of the minimum force F that can produce the same moment given in (1) about point B. Also find the value of 0 that 290 mm corresponds to this minimum force. 190 mm

Example 2: In order to tighten the bolt shown in the figure below, a force F is applied to the end of the curved wrench, Find: 1) The magnitude of the force F that produces a clockwise moment about the bolt center B of 40 N.m (take 0 = 25°), 2) The magnitude of the minimum force F that can produce the same moment given in (1) about point B. Also find the value of 0 that 290 mm corresponds to this minimum force. 190 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rectangular framework is subjected to the following non-concurrent system of forces: a 30lb- force below the origin, a 20 lb-force,3ft above the origin and making an angle of30°N of E, a 100lb-force with a horizontal distance of 3ft and a vertical distance of 4ftfrom the origin and making an angle of 45°NW , a 60lb -force with the same distance like the previous force but along the positive x-axis, and a 100lb- force 4ft tothe right of the origin and making an angle of 60° S of W . Determine the magnitude and direction of the resultant, as well as its moment arm relative to the origin.
15° Deltoid 17 cm 38 cm A young girl is holding her arm straight out parallel to the ground. Her arm is perfectly straight. Use the information given in the picture and below to solve problem 2. a) Draw and label the free body diagram of all forces on the shoulder b) Calculate the force of the deltoid using the sum of the moments. c) Find the vertical reaction force of the shoulder. Is it acting "up" or “down" לי Weight of the arm = 1[kg]
Select the correct statements regarding the equivalent force moment systems. (Select 3) If a force acting on a body is represented by another force /moment, such that the resulting rigid-body effects remain unchanged, the two systems are said to be statically equivalent This is a single force and pure moment acting at a single point that is statically equivalent to the original set of forces and moments. Only the system at Equilibrium state has equivalent force moment systems To find the "force" part of the equivalent system, add together all the force vectors.
You must solve all questions. The aluminum bar has a 40mm diameter and 600mm length. It is held stationary at the origin on the left end. On the right end is a wrench that is 70i+220j mm from the connection to the rod to where the force is applied. At that point, a force of -7000i+800j N is applied. a) What is the mass of the bar? b) What is the moment applied by the wrench? c) What is the maximum normal stress due to this moment? d) What is the yield factor of safety for this stress?
Figure Q1c shows a bracket on rollers that allow the bracket to move along a beam in the horizontal direction. A force F₁ of 2625 N acts at point A where the angle between F₁ and the x-axis is 100. If force F2 acts at an angle a = 40° between F2 and the y-axis: (1) (ii) Give your answers to the nearest newton (N) to 2 decimal places. Assume coplanar forces and assume horizontal rolling is frictionless. Determine the magnitude of F2 necessary to maintain bracket on horizontal equilibrium. Determine the vertical force at A acting along the y-axis. F1 0 y α Figure Q1c F2 X
Given: Find: Fc ● FA A r60° FC=.79 lbs theta C w/ horizontal= 36° r=.98 in r B Written work: Draw the direction of F smallest force at A to balance moment: Fa = ##.## lbs X
The following figure represents a bicep curl maneuver where the center of mass (CoM) of a 23 kg dumbbell is 0.29 m from the elbow joint (pivot). The mass of the arm is 5 kg and acts 0.17 m from the elbow joint, and the biceps tendon acts at a distance of 0.01 m from the elbow joint. A)The triceps produces a negligible force and the arm is at an angle of 15 degrees above the horizon. The given distances from the joint are the distances along the line that is 15 degrees above the horizon as shown in the figure. What magnitude of force in newtons (N) must the biceps muscle produce to hold the 23 kg mass in place (static equilibrium) b)
Example ( 2-1) : The ring in the figure below is subjected to two forces ( F1) and ( F2). Determine the magnitude and direction of the resultant force. 10° F, = 150 N F = 100 N %3D 15° Solution : Parallelogram Law. The parallelogram is formed by drawing a line from the head of F1 that is parallel to F2 , and another line from the head of F2 that is parallel to F1 , the resultant force FR extends to where these lines intersect at point A. The two unknowns are the magnitude of ( FR) and the angle ( 0) (theta).
/Find the two forces Fbc & Fac as shown :in the figure below Fab=30 N Fbc 50 30 Fac (Fbc=55 N and Fac= 70 N) O (Fbc=40 N and Fac= 50 N) O (Fbc=46 N and Fac= 59 N) O
Expiremental Method: Force Table F1 - 150N, 30° N of E F2 - 100N, 60° E of S 1) Find the Equilibrant Magnitude and Equilibrant Direction 2) Find Resultant Force Vector Magnitude and %Error 3) Find Resultant Force Vector Direction and %Error
An eye bolt is used to attach 3 cables to a steel plate. The tension in the three cables create F,=200 Ibf, F2=250 lbf, and F3=100 lbf with 0 = 30 degrees and p=27.1 degrees. If the eye bolt is in equilibrium, what is the x-component of the sum of other forces (reaction force) on the bolt? If you add up the three force vectors, the reaction force you are looking for will just be in the opposite direction to put the eye bolt in equilibrium. The x-direction is positive and to the right. Eye bolt rsteel plate Nut & Washer
F1 F2 F3 A B d b F4 D F5 Consider the following values: - a = 25 m; b = 5 m; c = 25 m; d = 5 m; F1 - 6 kN; F2 - 7 kN; F3 = 8 kN; F4 - 9 kN; F5 - 10 kN; a = 30°, 0 = 45° , B = 60° 1] What is the resultant moment of the five forces acting on the rod about point A? a) - 154.8 kN.m b) 111.9 KN.m c) - 174.6 kN.m d) 162.9 kN.m e) 214.1 kN.m 0-47.1 kN.m 2] What is the resultant moment of the five forces acting on the rod about point B? | a) - 209.3 kN.m b) 215.7 kN.m c) 311.6 kN.m d) - 98.9 kN.m e) 125.4 kN.m f) - 124.2 kN.m 3] What is the resultant moment of the five forces acting on the rod about point C? a) - 204 kN.m b) 121 kN.m c) 146 kN.m d) - 279 kN.m e) 241 kN.m D- 353 kN.m 4] What is the resultant moment of the five forces acting on the rod about point D? a) – 212.7 kN.m b) 182.7 kN.m e) - 21.9 kN.m d) 36.9 kN.m e) - 27.1 kN.m ) 30.1 kN.m 5] What is the moment of the force F2 about point E? a) 100.3 kN.m b) 118.1 kN.m c) 224.6 kN.m d) 193.1 kN.m e) 151.1 kN.m ) 221.3 kN.m E.