You must solve all questions. The aluminum bar has a 40mm diameter and 600mm length. It is held stationary at the origin on the left end. On the right end is a wrench that is 70i+220j mm from the connection to the rod to where the force is applied. At that point, a force of -7000i+800j N is applied. a) What is the mass of the bar? b) What is the moment applied by the wrench? c) What is the maximum normal stress due to this moment? d) What is the yield factor of safety for this stress?

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A: Given data: -  The force P is P = 212 N. The moment M is M = 663 N. The height of the region is h =…

Q: Given: Two forces are acting on a pipe as shown in the figure. The magnitude and the coordinate…

A: Coordinates of A,B and C are  A(-3 x sin40,3 x cos40,0) A(-1.928, 2.298, 0) B(4,-7,0) C(0,0,4)…

Q: For the following diagrams, determine the perpendicular component F, for each force shown, as well…

A:

Q: 5. A person pulls on a rope with a force of 100 lbs as shown below. What is the moment about point A…

A:

Q: An element of a solid is subjected to tensile stress of magnitude 40 MPa along the x-axis and…

A:

Q: Find the sum of the vertical forces in pounds if F1 = 30 lb at 60 deg N of W and 50 lb at 40 deg S…

A:

Q: Find the values of P and F so that the four forces shown in the figure will produce an upward…

A: Given data as per question Resultant force =300 lb The total length of bar =7' Taking moment about…

Q: 3) A point mass is attached to one end of a beam levered against a spike which acts as the pivot.…

A:

Q: W8 28uple forces Fi- 67N. F- 61N, act on the frame and given that d-4m and @-28. The other length…

A: Given: The frame is shown below:

Q: Q) A simplified model as shown in figure below of a planar robotic arm. You may assume that each…

A: As per the given data in question, there is no matching answer. Please find below the attached…

Q: 2000Lbs 30% 60° y A' \ B The bar OA is fully constrained at O and attached to the cable AB.

A: Given Data: The length of bar AB is 20'. The coordinate of point B is (8',16',0). The force in the…

Q: Calculate the total moment of the system about point A, when P1 = 8 kN, P2 = 10 kN %3D and 0 = 45°.…

A:

Q: P1: Given the structure below, find the total moment relative to point B due to the external forces.…

A: Given the structure below, To find- The total moment relative to point B due to the external…

Q: Find box for the given Plane, where by =120m, di=25m, bz=25m, dz=100m, by=80m & dy=25 m (Enter only…

A:

Q: F1 F2 a A B. F4 Consider the following values: - F5 a-7 m; b-3 m; a -7 m; d- 3 m; F1 3 kN; F2 11 kN;…

A:

Q: The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same…

A:

Q: The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on…

A:

Q: Q) The mass of lamp is 20 kg and geometry is as shown. Find the force in each cable. C 30° B 45°

A:

Q: The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on…

A:

Q: Q) A simplified model as shown in figure below of a planar robotic arm. You may assume that each…

A:

Q: For multiple choice, choose the best answer. Show all work: indicate your plan and draw FBD's (Free…

A:

Q: A mounting point for a wind turbine anchor has the geometry below. Determine the moment (put in…

A: Given: The tension is T=250 lbf, The angle from vertical is θ=45°, The width is w=3 in, The height…

Q: F1 F2 a F3 A F4 E B F5 Consider the following values: - a = 25 m; b = 5 m; c = 25 m; d = 5 m; F1 = 4…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: Q) Find the components of the forces G = 2 kN and K = 5 kN as shown in the * .following figure %3D G…

A:

Q: A young girl is holding her arm straight out parallel to the ground. Her arm is perfectly straight.…

A:

Q: The figure shows the forces P and Q of 300N and 400 N respectively applied at points B and C.…

A:

Q: 5.) If the resultant force (single equivalent force) of the given system is known to pass through…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.