ZV7ZAIN IQBigBlueButton - Reheat..t014.rna1.blindsidenetworks.com37:28Rankine Cycle...Ali Khaleel Kareem OHomeworkExample 2: 2.6 (Page 45)In a stream power plant, the steam mass flow rate is 80ton/h, the steam intersthe turbine at 6MPA and 480 °C, condenser pressure = 0.06MPA, mechanicaland electrical efficiencies are 0.96 & 0.95, respectively. Find the specificsteam consumption and the power output.Example 3: 2.7 (Page 46)Find the cycle efficiency and specific steam consumption of a reheat cycle(Error! Reference source not found.) operating between pressures of3MPA and 0.004MPA, with superheat temp of 450 °C. Assume that the firstexpansion is carried out to the point where the steam is dry saturated andthen the steam is reheated to the original superheat temp. The feed pumpterm may be neglected.

Example 2.26 :- You have posted multiple questions on single window. As per the guidelines I am…

Example 2: 2.6 (Page 45) In a stream power plant, the steam mass flow rate is 80ton/h, the steam inters the turbine at 6MPa and 480 °C, condenser pressure = 0.06MPA, mechanical and electrical efficiencies are 0.96 & 0.95, respectively. Find the specific steam consumption and the power output.

Example 2: 2.6 (Page 45) In a stream power plant, the steam mass flow rate is 80ton/h, the steam inters the turbine at 6MPa and 480 °C, condenser pressure = 0.06MPA, mechanical and electrical efficiencies are 0.96 & 0.95, respectively. Find the specific steam consumption and the power output.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the figure below, a reversible power cycle receives energy QH by heat transfer from a hot reservoir at TH and rejects energy Qc by heat transfer to a cold reservoir at Tc. Hot reservoir at TH Boundary- Cold reservoir 20 at Te (a) If TH = 1100 Kand Tc = 400 K, what is the thermal efficiency? (b) If TH = 500°C, Tc= 20°C, and Weycle = 1800 kJ, what are QH and Qc, each in kJ? (c) If n = 70% and Tc= 40°F, what is TH, in °F? (d) If n = 40% and TH = 1027°C, what is Tc, in °C?
* İl. Gmail ► Untitled docu.. A system consists of a turbine and heat exchanger are connected in series. The working fluid is entering the turbine at P1 0.6 Mpa, T= 200 °C and leaving it with P,= 0.2Mpa. Then the turbine exit becomes the heat exchanger inlet to increase the fluid temperature to become 800 °C. Considering that the adiabatic power y =1.4 and the specific heat = 1.005 KJ/Kg.K. Determine the turbine production work WT and heat exchanger energy needed to be added quE. T = 200 °C P,= 0.6 Mpa- T T2 ? P,=0.2 Mpa h high НЕ T= 800 °C P3 =? 9 in
This is Problem 13 of Chapter 3 in Sustainable Energy by Richard Dunlap, 2nd Edition. I need help solving it: A coal-fired generating station has an efficiency of 38% and produces an average electrical output of 1000 MWe.(a) How much coal does it burn per second (kg/s)? Assume the coal is bituminous.(b) How much heat (in joules) is released to the environment per second?(c) How many liters of water at 20°C could the heat in part (b) boil (at STP) per second? For c, here is my idea: use Q = mc(change in T). Here change in T is (100 C - 20 C) or 80 C and c = 4200 J/(kg C) so I can solve for m. Question: I need the density of water to find liters, but density changes with temperature. So, do I use the regular 1000 kg/m^3 or something else?
I need help with a review porblem I cannot solve! thank you Steam enters an adiabatic turbine at 4 MPa, 800K and exits at 8 kPa, 90% quality. Assuming steady state, steady flow conditions, determine: a) The power output of the turbine (MW) if the mass flow rate is 63kg/s. b)The volumetric flow rate at the inlet (m3/s).
Find the turbine specific work, y=0.143 state 1 2 3 45 9 10 kJ/kg 226 236.1670 3602 2796 3481 2494 702 Turbine Boiler 6. 8. 4 Mixing chamber Closed Condenser fwh 2 10 3 PII PI
The power generated by an adiabatic steam turbine is 5MW, when the steam enters the turbine at a pressure of 2.3MPa, a temperature of 400C and a speed of 50m/s; and leaves the turbine at a pressure of 15kPa, a quality of 90% and a speed of 180 m/s a) Represent the process on a P-V diagram. b) Find the mass flow rate of the steam. c) Find the exit area of the turbine.
4.1 A gas turbine power plant is operating as follows. Compressor intake air temperature T, is 306 K, pressure p, is 100 kPa, and compressor pressure ratio B is 15. TIT T, is 1490 K. Isentropic efficiency of compressor N, is 0.88, and that of turbine n is 0.91. Air mass flow rate mi, is 636 kg/s. Fuel mass may be ignored. Calculate (i) actual temperatures at compressor and turbine exits, (ii) plant actual net specific work per kg air, (iii) plant actual power output, (iv) plant actual rates of heat addition and rejection, and (v) plant actual thermal efficiency.
3.24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You find a used cross-flow exchanger (both fluids unmixed) in storage. It was previously used to cool 136 kg/min of NH3 vapor from 200°C to 100°C using 320 kg/min of water at 7°C; U was previously 480 W/m²K. How much air can you cool with this exchanger, using the same water supply, if U is approximately unchanged? (Actually, you would have to modify U using the methods of Chapters 6 and 7 once you had the new air flow rate, but that is beyond our present scope.)
Ts diagrams for two reversible thermodynamic power cycles are shown in the following fig- ure. Both cycles operate between a high temperature reservoir at 500 K and a low temperature reservoir at 300 K. The process on the left is the Carnot cycle described in Section 2.9. The process on the right is a Brayton cycle, which is similar to a Carnot cycle, except that the two steps (state 1 to state 2) and (state 3 to state 4) are at constant pressure. Which cycle, if either, has a greater efficiency? Explain.
Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.
Separate streams of steam and air flow through the turbine and heat exchanger arrangement shown in the figure below, where air enters location 5 at a rate of 1000 kg/min. The left turbine (Turbine 1) is able to produce 12,000 kW of power. Steady-state operating data are provided on the figure. Heat transfer with the surroundings can be neglected, as can all kinetic and potential energy effects. W2 = ? Turbine Turbine 2 P3 = 10 bar T3 = ? T2 = 400°C_ P2= 10 bar T = 240°C P4 = 1 bar Steam in P1 = 20 bar +6 T = 600°C www T5 = 1500 K -5 Ps = 1.35 bar Heat exchanger V T = 1200 K P6 = 1 bar Air in Determine: T3, in °C. • the mass flow rate of steam at 1, in kg/s. • the power output of the second turbine, in kW. • the magnitude of heat transfer between the steam and air, in kW. • the direction of the heat transfer (i.e., to the steam or from the steam).
You have a tank that is 0.01 m^3 and is initially evacuated. You then hook this up to a line that supplies N2 at a pressure of P_1 = 5 bar and a T_1 = 350 K. The tank fills adiabatically (you can assume there is no heat flow to the walls of the tank), and the filling ends when no more N2 flows into the tank. Find a) the final pressure of the gas in the tank, and b) the final temperature of the gas in the tank. You can assume N2 is an ideal gas with a CP* = 29 J/mol K. NOTE: Mainly I am confused on how the evacuated tank factors into the work for b). What I did was use the ideal gas formula to find a value for N2*T2 (601.395) but I am no longer certain how to continue in the work. I was assuming the practice question had meant the temperature of the tank was 0 initially but it leads to a negative mole value. For a) I got 5 bar, arguing the flow would stop when the pressure of tank and line are equal