Example (1-2): A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface elevation = 170 m). The suction pipe is 45 m long (friction factor, f = 0-024) and 35 cm in diameter. The delivery pipe is 950 m long (f =0-022) and 25 cm in diameter. The head discharge relationship for the pump is given by Hp = (90 - 8000 Q²), where Hp is in metres and Q in m³/s. Calculate: (i) The discharge in the pipeline. (ii) The power delivered by the pump.

Example (1-2): A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface elevation = 170 m). The suction pipe is 45 m long (friction factor, f = 0-024) and 35 cm in diameter. The delivery pipe is 950 m long (f =0-022) and 25 cm in diameter. The head discharge relationship for the pump is given by Hp = (90 - 8000 Q²), where Hp is in metres and Q in m³/s. Calculate: (i) The discharge in the pipeline. (ii) The power delivered by the pump.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: single hydraulic turbine is to be selected for a power site with a net head of 30 m. 10 700

Q: wo chambers, Chamber 1 and Chamber 2 where the pressure at chamber 1 p1=70 kPa, at chamber 2 the…

A: Given:P1=70 KPaP2=5 KPad=6 cm =0.06 mCc=1Cv=0.95h=1.8 ms=2.5

Q: The mechanism shown in figure is Brake shoe used to investigate the power produced by Pelton wheel…

A: The power obtained at the exit of runner is termed as runner power or turbine power. This is the…

Q: A pump has the following parameters N= 2133.5 RPM, Ns = 40 RPM, D = 37.1 cm and is used to pump…

A: As per the guidelines, I can solve only 1st three sub-parts. For rest parts, please re-post again.…

Q: Q2:- The tank as shown in figure below (Diameter=1.5 m Length= 3.5 m) is full with Fuel and the Fuel…

A: An orifice is a hole on the side or base of a tank containing liquid that allows liquid to flow…

Q: 4. In a pumping system handling water, the surface level of water in the open suction tank is 3m…

A: Answer: (a) The total head loss due to friction is 25.14 m. (b) The total dynamic head is 50.14 m.…

Q: A pump works between two opened tanks tnrougn a o10 cm diameter and length of 30 m with a pump is…

A: Given information: S.G. of oil=0.83 Pressure at point 1, P1= 74.6 psig Pressure at point 1, P2= 62.2…

Q: A pump receives water from a tank. If the pump needs 24 n of NPSHA, how high must the water level…

A: Let H be the height of the water level above the pump centreline.

Q: Two chambers, Chamber 1 and Chamber 2 where pressure at chamber 1 p1=70 kPa, at chamber 2 the…

Q: Q.2) As shown in the figure, gasoline (p=701 kg/m3, µ=0.51x10-3 N.s/m2) will be extracted from a…

Q: eter is A petroleum product is pumped at a rate of 2.32 x 10'm/s from a reservoir under atniospheric…

A: Given: The flow rate, Q = 2.32 x 10-3 m^3/s The height to be pumped, hd = 177 cm = 1.77 m The pump…

Q: Galvanized iron pipes with a roughness height of 0.40 cm are used to deliver water from reservoir A…

Q: A 70 cm diameter centrifugal pump which is dynamically similar to the tested pump tabulated above,…

Q: The diagram in figure mm diameter to a very large tank where the free water surface is assumed to…

Q: The variation of pump head, efficiency, and required ENPY parameters with flow rate obtained from…

Q: A pump has a characteristic curve described by the equation: hp = 15 - 0.2 x Q2 What is the pump…

Q: Water from a reservoir is pumped over a hill through a pipe 900 mm in diameter and a pressure of one…

A: Given:Pipe diameter, d=900 mm=0.9 mPressure at the pipe discharge, P2=1 kg/cm2=1*98.1 kPa=98.1…

Q: Find the pressure difference in inlet cross section of water sprayer as shown in the figure (D=10…

Q: What is the required pump power (P.) for the system below? • The source reservoir is on the right…

A: Given:Discharge rate, Q=0.11m3/sPipe length, L=180 mPipe diameter, d=0.2 mFriction factor,…

Q: 1 Acentrifugal pump running at 500 rpm and at its maximum efficiency is delivering a head of 30 m at…

Q: The velocity of water is measured using an orifice meter (throat diameter = 0.06m) in a 0.31-m…

A: In this, it is asking for the answer for the second question only so we will provide the answer for…

Q: Imagine that you are recently bought a 2-floor house and want to improve the water installation at…

A: Given that, Height of top flor from water meter, z2=15 m,Pressure inside the pipe, P=200…

Q: norizontal

A: given:

Q: Pressurized air 2.5 m A pressurized tank is filled with water as shown in figure. The absolute…

A: Here, Let us take values before outlet be represented by subscript 1 and values after outlet be…

Q: Using the pump selection table below to determine the best pump for the given condition: • A flow of…

A: Option ( C ) is correct 100-80/20

Q: Assume a mass flow rate of 13 kilogram-force per second. The fluid is moving through insulated pipe…

Q: Q3: Two tank are connected with piping system as shown. If the pump chara given by: hp- 31-120000…

Q: b) Water is pumped from a lower reservoir and then discharged into the atmosphere as shown in Fig.…

A: Given:Q=1400 L/min =1.460 m3/sρ=997 Kg/m3μ=0.891*10-3 Kg/m.sz2-z1=7 mD=120 mm =0.12 mL=40 m

Q: ter is 1025 kg/m³. Calculate (a) the quantity of water flowing through each A tidal km. The…

A: The given problem relates to power generation through tidal energy. There are 140 generators which…

Q: (1) Water Pump m L To double the outflow of a reservoir, a pump is added as shown in the Figure…

Q: A pump rated at 65% efficiency is used to transport water from a large open reservoir to a point 10m…

A: Dear student, According to guidelines, I am allowed to answer only one problem…

Q: The variation of pump head, efficiency, and required ENPY parameters with flow rate obtained from…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Example (1-2): A pump delivers water from a tank A (water surface elevation =110
m) to tank B (water surface elevation = 170 m). The suction pipe is 45 m long (friction
factor, f = 0-024) and 35 cm in diameter. The delivery pipe is 950 m long (f = 0·022)
and 25 cm in diameter. The head discharge relationship for the pump is given by Hp =
(90 – 8000 Q²), where Hp is in metres and Q in m³/s. Calculate:
(i) The discharge in the pipeline. (ii) The power delivered by the pump.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: head loss in suction and delivery pipe

VIEW

Step 3: discharge and power of the pump

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

q4
A pelton wheel is supplied with water under a head of 100 m at the rate 1000 litres/s. The bucket deflects the jet through an angle of 160°. The mean speed of bucket is 20 m/s. Find : Mass flow rate of water (i) (ii) Velocity of jet (iii) Power output H. V2 V2 160° C $ = 20° A V1 =Vw1
B3
A pump is used to take water out of a large lake and deliver it to a farm to be used for irrigation. The pump location is illustrated in the figure below, where the suction side of the pump (also called the pump intake) is 3 m above the water surface in the lake and the vertical intake pipe has a diameter of 150 mm. (Discharge side) Pump - >100 L/s P (Suction side) 3m -150 mm Lake Part A Assuming that viscous effects are negligible, what is the pressure on the suction side of the pump when the flow rate through the system is 100 L/s? Express your answer to three significant figures and include appropriate units.
Don't give handwritten solution
Explain and Plot the whole process why the head(h) arrive in meter(m) unit and value and why the pump work(Pw) arrived in kilowatts(KW) unit and value Thanks!
KL „Pump Reservoir 80m Well Figure 1 Your family has a small farm which needs to be watered by pumping water from a nearby well. The water needs to be continuously supplied at a rate of 0.003 m³/s through 6-cm internal diameter cast iron pipcs. The total required length of piping is measured to be 350m, with an angle valve fully open (KLvalve), a sharp-edged entrance (KLent), a rounded exit (KLexit) and ten threaded 90° bends (KLelbow). Take the efficiency of the pump to be 0.75, density and viscosity of water to be 1000 kg/m³ and 0.00131kg/m.s, respectively. Use Moody diagram for friction factor. i. Find the total head loss, httotal given that the pipe diameter is constant. ii. Determine the rated power of the pump that needs to be purchased, in kW. iii. Propose one practical way to reduce the total head loss, hL.total
Estimate pump power requirement for Hpump = 58.598 m and npump = 0.60. Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kelbow = 0.26 f = 0.019 γ = 9810 N/m3 Choices: 197 kW 179 kW 279 kW 297 kW None of the Choices
Drinking water from a large bottle placed on high ground references Inside the Damacana with an on / off valve at the end a plastic hose is immersed. On/off valve of hose with diameter 3 mm the found tip is 80 cm below the ground. Water in Damascus (P = 1000 kg/m3) fill a cup with a volume of 0.2 L for the state that the level is 60 cm calculate the time required. Casualties are negligible. 60 CT 80 m Please choose one:
Water flows through pipe A whose diameter is 30 cm and into parallel pipes 1, 2 and 3 and out through Pipe B (diameter= 30 cm). The properties of the pipe are as follows: for pipe 1, L= 300 m, diameter = 10 cm f= 0.020; for pipe 2 L= 240 m diameter= 15 cm f= 0.018 and for pipe 3, L= 600 deiameter= 20 cm f= 0.017. The upstram junction has an Elev. 90 m with pressure of 205 kPa; the downstream junction is at Elev. 30 m. If the average velocity in pipe A is 3.0 m/s, find the flow rate in pipe 3. Provide FBD and choose the right answer below a.24.68 L/s b.212.0 L/s c.80.21 L/s d.107.11 L/s Clear my choice
(a) Water flows by gravity from one lake to another as illus- trated; the surface levels of the lakes differ by an eleva- tion of h= 50 ft. If the volumetric flow rate is steady at Q = 80 gallons per minute, what is the associated loss of available energy? (b) A pump is to be installed to pump the water from the lower lake to the upper lake with the same flow rate as above (Q = 80 gpm). If the amount of energy loss is assumed to be the same as in part (a), how much mechanical power must be supplied by the pump? Answer: (a) loss = 1600 ft-lb/slug, (b) Wpump = 2.0 hp
A pipe with diameter 30 cm carries oil of sp.gr. 0.95 at a velocity of 4 m/s .at another section the diameter change to 20 cm. Find the velocity at this section and also find the mass flow . rate of oil A- V=8.5m/s , m= 270 kg/s B- v=9m/s, m= 300 kg/s O C- v=9 m/s , m=269.8 kg/s D- v= 9.5 m/s, m= 280 kg/s O