Examining and modifying the contents of the 8086's internal registers1. Use the REGISTER command to display the current contents of all the internal registers bytyping R.o List the values of the following registers:BXDXIPSPCSDSo What is the address of the next instruction to be executed?2. Enter the command: R AH (hit ) What happens and why?3. Use a REGISTER command to first display the current contents of BX and then change thisvalue to 0020h.

It is defined as a small set of data holding places that are part of the computer processor. A…

amining and modifying the contents of the 8086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers: AX BX DX DS o What is the address of the next instruction to be executed? 2. Enter the command: R AH (hit ) What happens and why? 3. Use a REGISTER command to first display the current contents of BX and then change this value to 0020h.

amining and modifying the contents of the 8086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers: AX BX DX DS o What is the address of the next instruction to be executed? 2. Enter the command: R AH (hit ) What happens and why? 3. Use a REGISTER command to first display the current contents of BX and then change this value to 0020h.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter6: System Integration And Performance

Section: Chapter Questions

Problem 10VE

See similar textbooks

Similar questions

1. Write an instruction sequence to save the current content of the flag in memory location MEM1 and then reload the flags with the contents of memory location MEM2. LAHF MOV MEM1, AH MOV AH, MEM2 SAHF HLT 2. Verify the operation of the following instructions that affect carry flag, start with CF = 0. CLC STC СМС 3. Write an instruction sequence to configure the 8086 as follows: Interrupts not accepted; Save the original contents of flag SF,ZF,AF,PF and CF at the address [0700H], then Clear the carry.
6. Update memory values for the following code. Keep track of the loop counter (R16) and index register values as you go through the loop. LDI R16,3 R15, Y+ -Z, R15 LOOP: LD ST DEC R16 BRNE LOOP STS 0x0200, R28 CPU Register R28 (YLB) R29 (YB) R30 (ZUB) R31 (ZHB) Value OxFC 0x01 0x04 0x02 Data Memory Value 0x21 0x02 0x11 0x03 Address 0x01FC 0x01FD 0x01FE Ox01FF Ox0200 0x0201 Ox0202 Ox0203
Instruction: Analyze the given Emu8086 assembly codes and answer the following questions. Note: You can execute the program if you have the Emu8086 Emulator installed on your computer. What is the purpose of the next: section in the program? What is the purpose of al and bx in the program? In the print: section of the program, what does the jz instruction perform? In the print_al procedure of the program, what does the jne instruction perform? In the print_al_r: section of the program, what does the je instruction perform?
Instruction: Analyze the given Emu8086 assembly codes and answer the following questions. Note: You can execute the program if you have the Emu8086 Emulator installed on your computer. What is the purpose of Lines 39-40? What is the purpose of Lines 49-50? What is the purpose of the next: section in the program?
Calculate the Physical and the Logical addresses for the memory instructions
Review Questions 1. A segment is an area of memory that includes up to 2. How large is a segment in the 8086? Can the physical address 346E0 be the starting address for a segment? Why or why not? 3. State the difference between the physical and logical addresses. 4. A physical address is a 5. Which register is used as the offset register with segment register CS? 6. If BX = 1234H and the instruction "MOV [2400],BX" were executed, what would be the contents of memory locations at offsets 2400 and 2401? bytes. -bit address; an offset address is a -bit address.
MCQ select more than one in c programming
4. Consider the following instruction: and $t0, $e5, $3 a. What are the values of the control signals generated by the control unit for the above instruction? RegDst Jump Branch MemRead MemtoReg MemWrite ALUSrc RegWrite
1. What instruction (mov, Idr, Idrb, str, strb) is used to... a. Put a byte from memory into a register b. Put a register value into another register c. Put the address of a label into a register d. Put a register value into a memory address e. Put an immediate into a register 2. Which instruction (move, load, or store) lists the source followed by the destination? 3. What punctuation is used to indicate you're reading the address of a label? 4. What punctuation is used to indicate the register value is to be treated as an address? 5. Assuming the following is at the start of the data section: Array2 dcd 45, 23, 67, 31 a. What would be in r0 after 1dr r0, Array2 executes? b. What would you add to rO to have the address point to the 2nd value in the array? 6. (Bonus worth 0.2 points) Given our simulator's configurations, etc., if r2 = 0x0800001C, what value(s) in memory would be changed by str r1, [x2] ?
Which statement is correct for the memory segments in 8086 microprocessor? a. For Stack segment, the offset address can be a direct value. b. The offset address for program instructions is taken from SP register. c. Variables created in the Assembly program are stored in Data segment. d. Segment address for executing sub-routines is taken from ES register.
1) How many address lines in the 8086 microprocessor? 2) How many data lines in the 8086 microprocessor? (choose the correct one) When the M/IO line is high (1) that means the CPU has: a) memory operation b) input/ output operation 3) name the segment registers on 8086 microprocessor 4) name the date registers on 8086 microprocessor 5) name the index and base registers on 8086 microprocessor. 6) What is the size of each of the following registers? AH, DL , CX, SS, SP, IP 7) When does the CF become 1 or 0? give two examples. 8) When does the ZF become 1 or 0? give two examples. 9) When does the PF become 1 or 0 ? give two examples. 10) What does it mean when the SF =1? give an example. 11) How much memory can the 8086 processor address? 12) Write a program in 8086 microprocessor to find out the largest among 8-bit n numbers, where size “n" is stored at memory address 2000 : 500 and the numbers are stored from memory address 2000 : 501 and store the result (largest number) into memory…
1. Create a program using the ARMv7 instruction set to do the following: o Read a single pushbutton o Output a 0 on a seven segment display when the button is pushed in o Output a 1 on a seven segment display when the button is not pushed 2. Create a program using the 8086 instruction set to do the following: o Read 2 single digit numbers from keystrokes of the keyboard using interrupts o Add the two single digit numbers o Display the numbers using interrupts