5. The stack memory is addressed by a combination of thesegmentplus_offset.6. The PUSH and POP instructions always transfer-bit numberbetweenthe stack and a register or memory location in the 8086 microprocessors.7. For string instructions, DI always addresses data in thesegment.8. The 8086 LOOP instruction decrements registerand tests itfor a 0 to decide if a jump occurs9. The last executable instruction in a procedure must be10.A bus cycle is equal to clocking.periods.11. If A0 is a logic 0, then thememory bank is selected.12.the 8086 processor is partitioned into two logical units------------ andC.13. ------- is the value of the control word register (CWR) of PPI 8255 if allports are input14.Fixed address for I/O instructionsbytes while Variable address for------ ---bytesI/O instructions is15. Write bus cycle need-clocks to complete one write of data tomemory

All the correct solutions for the problem are shown below. Solution 5) SS plus either SP or…

Answered: The stack memory is addressed by a…

Engineering

Computer Science

The stack memory is addressed by a combination of the plus_ offset. segment

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Computer science
Notes: C language Drawing a Flow Chart is a must. 1. Write a program that adds all odd numbers within the numbers from n to m. the values of n and m are read from the terminal. 2. Write a C program that ask the user to enter a character then the program will print the input character and the next characters in ascending order up to character 'Z'. (Note: if the user enters lower case character, the program will print lower case character and vice versa)
Briefly explain overflow flag
what is the difference between void type pointer amd simple pointer?
Identify the difference between STACK and ARRAY.
AIM- Write an 8085 sequence to check whether the first set of reading is higher than the second one or not. PROBLEM STATEMENT- The pressure of two boilers is monitored and controlled by a microcomputer works based on microprocessor programming. A set of 6 readings of first boiler, recorded by six pressure sensors, which are stored in the memory location starting from 2050H. A corresponding set of 6 reading from the second boiler is stored at the memory location starting from 2060H. Each reading from the first set is expected to be higher than the corresponding position in the second set of readings. Write an 8085 sequence to check whether the first set of reading is higher than the second one or not. If all the readings of first set is higher than the second set, store 00 in the 'D' register. If any one of the readings is lower than the corresponding reading of second set, stop the process and store FF in the register 'D'. Data (H): First set: 78, 89, 6A, 80, 90, 85 Second Set:71, 78,…
plese modify the code according to the instruction in c programming Please Modify this code according to this instructions cmds.c – Need to modify the Cmd struct to include: “ms” and “h” – Add code in mem_display(), help(), mem_set() functions – Command routine calls with 2 arguments, e.g. mem_display(Cmd *cp, char *arguments) &cmds[0] Address of the string “10000” – If we enter a command “md 10000” to display the contents of 16 locations starting with 10000, the arguments passed are: file: cmds.c /* the Makefile arranges that #include <..> searches in the right places for these headers-- 200920*/ #include <stdio.h> #include "slex.h" /*===================================================================* * * Command table for tutor program -- an array of structures of type * cmd -- for each command provide the token, the function to call when * that token is found, and the help message. * * slex.h contains the typdef for…
assembly language hcs12 Write a program which prompts user to enter a character, if the user presses ‘W’, the program calls a subroutine which loads a value $3D in register ‘A’, XOR’s register A with $6F and displays the result in hexadecimal result on screen.
(True/False): Local variables are created by adding a positive value to the stack pointer
It is possible to see the function's return address by issuing a set of instructions. It's important to remember that modifying the stack shouldn't prevent the process from returning to its caller.
The default constructor of the array based stack class set the array data to zeros Select one: True False
PART 2: REPETITION CONTROL STRUCTURE (WHILE, DO-WHILE) Instruction: A mathematician named Ulam proposed generating a sequence of numbers from any positive integer N greater than 1 using the following procedure: If N is 1, stop. If N is even, replace it with N/2. If N is odd, replace it with 3 * N + 1. Continue with this process until N reaches 1. Here are some examples of the Ulam sequence for the first few integers. 2, 1 3, 10, 5, 16, 8, 4, 2, 1 4, 2, 1 5, 16, 8, 4, 2, 1 6, 3, 10, 5, 16, 8, 4, 2, 1 Create a java program using while/do-while that accepts as input an integer value N (assume N> 1) and prints out the Ulam sequence that begins with the input value N. Sample Input/Output: Depicted below are sample outputs when the program is executed (the items in bold characters are input from the user, while the items in bold italic are calculated and printed by the program): Input N: 14 Ulam Sequence: 14, 7, 22, 11, 34, 17, 52, 26, 13, 40, 20, 10, 5, 16, 8, 4, 2, 1 Input N: 5 Ulam…