Examination of the timing diagram of the 8237A indicates that once a block transfer begins, it takes three bus clock cycles per DMA cycle. During the DMA cycle, the 8237A transfers one byte of information between memory and I/O device. a. Suppose we clock the 8237A at a rate of 5 MHz. How long does it take to transfer one byte? b. What would be the maximum attainable data transfer rate? c. Assume that the memory is not fast enough and we have to insert two wait states per DMA cycle. What will be the actual data transfer rate?

Q: If the clock rate is 3.5Ghz, and data transfer unit size is 2 bits, calculate bus DTR(data transfer…

A: Dear Student, The detailed answer to your question along with step by step explanation is given…

Q: Do you prefer asynchronous or synchronous buses in terms of the amount of processing power and…

A: Synchronous buses operate on a clock signal, which synchronizes data transfers between components.…

Q: Construct a bus system with MUXs for 6 registers each of 8 bits.

A: Given:

Q: design an 8 bit common bus based circuit that supports addition of two 8 bit values. There are two…

A: The outputs of all the registers except the OUTR (output register) are connected to the common bus.…

Q: A certain computer’s Datapath takes 3.86 ns to load data from registers, 13.94 ns to execute the…

A: Given, Datapath takes 3.86 ns to load data from registers  13.94 ns to execute the ALU 5.99 ns to…

Q: What are the pros and cons of a serial bus as opposed to a parallel bus?

A: Introduction:- While slower and having a smaller bandwidth than parallel buses, serial buses are…

Q: the pros and cons of using a serial bus to send information instead of a parallel bus

A: What are the pros and cons of using a serial bus to send information instead of a parallel bus?

Q: Is there any benefit to using a serial bus instead of a parallel bus when transferring data from one…

A: The act of exchanging data between two or more digital devices is called data transmission. Analog…

Q: How many tri-state buffers would be required to make a bus that has 16 interacting components?…

A: A three-state bus buffer is an integrated circuit that connects several data sources to a single…

Q: When it comes to transferring data, what are the pros and cons of using a serial bus as opposed to a…

A: Introduction: In computer architecture, buses are a set of wires used to transfer data between…

Q: What are the pros and cons of using a serial bus to send data instead of a parallel bus?

A: Introduction: In computer architecture, buses are a set of wires used to transfer data between…

Q: Question 4 Why must the single-cycle datapath have separate instruction and data memories? The…

A: answer is

Q: A particular SDRAM system uses 24-bit addresses. There are 2 ranks in the system and the burst…

A: Solution:--   1)The given question has required for the solution to be provided with purpose of the…

Q: It is almost hard to find a happy medium between the performance of the processor, the memory, and…

A: A processor is a small chip used in computers and other electrical devices to carry out various…

Q: 2. bus capacity Assume a bus is 16 bits wide. The data and address lines are multiplexed, meaning…

A: Given Data : Bus size = 16 bits Data to transfer = 15 MB Bus frequency = 300MHz

Q: A 16Kx4 memory uses coincident decoding by splitting the internal decoder into X-selection (Row…

A: 16Kx4 memory uses coincident decoding by splitting the internal decoder into X-selection(Row…

Q: Assume a bus is 16 bits wide. The data and address lines are multiplexed, meaning that the bus must…

A: Solution:-

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.