Ex.5: Caution: The Lamps in this part of the ex are functioning normally10 VL1 (10V. 20 Ww)L2 (10V, 0.2 A)a. Find the resistance of lamp (1)b. Find the resistance of lamp (2)c. Compare the currd. Which lamp will have a higher brightness?e. Find the equivalent resistance Reg of the grouping of (L1) and (L2).f. Find the value of the main current I.g. If lamp (2) was switched with another lamp (L’) with indications (0.2 A, 10W). Will itfunction normally? If not, will be underpowered or overpowered? *Hint: Calculate theneeded voltage for normal functioning of lamp (L').Ex.6:Ii and I2 present in lamp 1 and lamp 2.I.Caution: The Lamps in this part of the ex are functioning normallyLamp one carries the following indications: (6V, 12W)Lamp two carries the following indications: (3V, 2A)PaL;BFig. 1a. Calculate the resistance of (L1)b. Calculate the resistance of (L2)c. Calculate the equivalent resistance of the combination of the two lamps.d. Find the value of the main current in the circuit.e. Which lamp will shine brighter?

As per Bartleby guidelines we are allowed to solve only one question with maximum three subparts,…

Ex.5: Caution: The Lamps in this part of the ex are functioning normally 10 V L1 (10V. 20 W). L2 (10V, 0.2 A) a. Find the resistance of lamp (1) b. Find the resistance of lamp (2) c. Compare the currents I1 and I2 present in lamp 1 and lamp 2.

Ex.5: Caution: The Lamps in this part of the ex are functioning normally 10 V L1 (10V. 20 W). L2 (10V, 0.2 A) a. Find the resistance of lamp (1) b. Find the resistance of lamp (2) c. Compare the currents I1 and I2 present in lamp 1 and lamp 2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Choose the correct answer to three questions only
This multiple choice Questions from MEASUREMENTS INSTRUMENTATION course.
Determine the voltage across resistor R2. (assume Zener voltage is 3 volts)
What is the value of VR
Explain how this circuit diagram works. Note: When the circuit receives light, the motor begins to run, and when there is no light, the motor stops. This circuit is used for an automatic curtain that opens when there is sunlight and closes when there is no light.
Which of the following statements is true ? OA. Power is additive in series and parallel circuits. O B. A battery is a current source. OC. In a closed circuit, current leaves the positive terminal of a battery, and is used up by the time it reaches the negative terminal. O D. Current only flows through the path of least resistance.
In the circuit, Determine: a. the total resistance (R7) of the circuit in kl. (. . places for the final answer) b. the current flowing in mA for each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the 12V final answer) c. the voltage in V across each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the ; use 2 decimal R = 3000 R3 = 4000 R2 = 1000 R4 = 1ka %3! final answer)
Three resistors R1,R2, and R3, are connected in series and to a 120-volt source. If R2 = 2R1, R3 = 3R1, and the total power taken by the circuit is 200 watts, calculate (a) the resistance of each resistor, ( b) the power in each resistor
Step 5: Calculate the voltage across resistor R6 (VR6) [mV]. Use the resistance values from step 3 as follow R5 = 211.51ohm andR6 = 1420.86ohm. For the calculation of VR5 close Switch 1 and leave Switch 2 open. For the calculation of VR6 close Switch 2 and leave Switch 1 open. Use the circuit diagram of figure 1. Step 6: Calculate the maximum power absorbed by resistor R5 (PR5)[μW] and the maximum power absorbed by resistor R6 (PR6) [μW]. Use the resistance values from step 3 as follow R5= RTh(a,b) and R6 = RTh(b,c). Vs = 1.5V R1 = 4700ohm R2 = 2200ohm R3 = 6800ohm R4 = 2700ohm VR2 = 0.253V VR4 = 0.311V VR5 = 254mV
Q: A wood panel containing 16 solar cells. Calculate the total open circuit voltage and short circuit current coming out of the board and draw the relationship between current and voltages in the following cases 1- If you connect each two cells in series and connect the groups in parallel. 2- If all four cells are connected in parallel and the groups are linked in succession, noting that each cell has the following characteristics: Vos = 0.75V, Isc = 2 mA
E8
b) Assume that all lamps are identical. In this condition from your opinion which lamp(s) having more brightness, and which Lamb(s) will be low brightness as shown in figure2. A B E VT Figure 2