5.3 Classify the following soils by the AASHTO classification system. Give the groupindex for each soil.Sieve analysis-Percent finerLiquidlimitPlasticityindexSoilNo. 10No. 40No. 2009880725221907458381284716441141007882328068483011ABCDE

Answered: Image /qna-images/answer/068d07cc-1d8c-496f-be3d-9a86d60abc06.jpg

Answered: ex for each soil. Sieve analysis-…

Engineering

Civil Engineering

ex for each soil. Sieve analysis- Percent finer Li

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Explain why clay materials are naturally hydrophilic

A: Clays and the most other natural minerals which are used in the drilling fluids, such as the barite…

Q: Sieve # Maas retained (gr) 4 0 10 11,5 16 11,7 20 12 30 12,9 40…

A: The grain size distribution may be defined as the particle size distribution of sand or granular…

Q: Describe the Dispersive clays.

A: Dispersive clays vary from ordinary clays which are erosion resistant since their relative content…

Q: TEEB PL= Soil Sieve Liquid Analysis(Percentage Limit Finer No. 4 87.4 No. 200 8.9 34.7 PI 29.9 of Cu…

Q: For the given slump380mm and maximum size of coarse aggregate=19mm determine the The minimum…

A: Given, Slump =80 mm Maximum size of coarse aggregate= 19 mm

Q: What is the upper size limit and lower size limit of sand

A: Soils can also be classified according to size, and the groups are further divided into fine,…

Q: Name the various ways of testing for dispersive clays.

A: The dispersive clay can be defined as it is a particular type of soil material in which the clay…

Q: Q/ What the purpose from sand content measurement, what is the acceptable percentage and size…

A: Sand content measurement is the sand volume which includes void spaces between the grains which are…

Q: If the volume of voids is cqual to the volume of solids in a soil mass, then the porosity of the…

A: Given data : Volume of solid=VSVolume of void=VVVV=VS

Q: Classify: This sand has 61% predominately fine sand, 23% silty fines, and 16% fine subrounded gravel…

A: This sand has 61% predominately fine sand 23% silty fines 16% fine subrounded gravel size. The…

Q: Soil classification requires all of the results of the following tests: Liquid limit and Plastic…

A: soil mechanics : Soil mechanics, a branch of soil physics and applied mechanics describes the…

Q: Q2. Using the sieve results of a batch of sand and gravel shown in the table below,calculate the…

Q: A sample of dry soil is coated with a thin layer of paraffin and has a mass of 450 gm. It displaced…

Q: LL=24% and PL=21% Classity the soll using A. USCS (GROUP SYMBOL IS | GROUP NAME IS B. AASHTO (GROUP…

A: Unconfirmed Compressive Strength is generally referred to for the maximum axial compressive stress…

Q: COMPLETE TABLE ASAAP

A: Solution: Liquid limit: Sample 1: percentage moisture=weight of water Weight of oven dried…

Q: Based on the sieve analysis a soil has % finer for the following sieves: No. 10- 80% ; No. 40- 68%…

A: Given : LL = 30 PI = 11 and % finer for sieves Required : Aashto classification of soil

Q: For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL= 32. Classify the…

A: Given % fine of different sieves Liquid limit, LL = 60 plastic limit, PL = 32 REQUIRED soil…

Q: A 6ft clay layer reaches 100% consolidation in 10 years and has a natural water content of 75%, what…

A: Thickness of clay layer, time taken for primary consolidation,natural water content,

Q: Table 1- Sieve Analysis Results Sieve and Retained Retained Cumulative Cumulative Opening Size (mm)…

A: Given data,

Q: Explain and state visual stability index, if in slump flow test there occurs clear segregation and…

A: Solution: Visual stability method is used for determining the stability of segregation of mixture…

Q: percentage of shrinkage moisture

Q: 02) One sample of different sands was found to have the following amounts retained on rach sieve.…

A: Given the data on amounts retained on each sieve in a sieve analysis. The aggregate grading curve…

Q: Soil resistance to failure is provided by its shear strength. How is shear strength developed in…

A: A crucial characteristic of soil is shear strength, which affects how resistant it is to failing…

Q: What is the soil type based on the USCS classification cent paing Sieve#4, 52% Per nt pass g…

A: Step1:Look at the % passing through sieve no 200=10<50%⇒COARSE GRAINED SOIL

Q: If you have 3/4-inch NMAS with a dry rodded unit weight of 93 lb/ft^3,a fineness modulus of 2.5 for…

A: Nominal maximum aggregate size (NMAS) = 3/4-inchDry rodded unit weight = 93 lb/ft^3Fineness modulus…

Q: iven the amount of soil retained in the #4 sieve is 45g, soil retained in the pan is 108g and the…

A: Given data :- Mass of soil retained over #4 sieve = 45 g Soil retained on pan = 108 g Total mass of…

Q: What equipment is typically required to conduct a sieve analysis test

A: We need to describe which equipment is typically required to conduct a sieve analysis test

Q: Soils with a particle size of retained on sieves #4 and above are collectively known as O gravels…

Q: Vacuum pump is an equipment being used in water content determination test O compaction test…

A: Given data in question Vaccum pump To find out Among which vaccum pump is used.

Q: Define Berardi et al. (1991) Modulus Reduction ?

A: Solution: Berardi presented an alternative method for estimating the footings settlement on the…

Q: If 1000 gms of sand is sieved through 4.75 mm, 2.36 mm, 1,18 mm, 600 micron, 300 micron and 150…

Q: ) What does the fineness modulus mean? What does it tells you about the sand?

A: The fineness modulus is a numerical measure of average particle size used in civil engineering to…

Q: For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL=32. Classify the…

Q: Define Drained Versus Undrained Strength

A: The drained strength of the soil is the strength of the soil calculated when the valve is opened…

Q: Explain how the maximum bulk density and optimal moisture content is determined using the proctor…

A: Proctor test

Q: Define In situ testing

A: In situ tests are conducted on the soil at the site. This is the Latin word, known as in position or…

Q: C. Using the sieve results of a batch of sand and gravel shown in the table below,calculate the…

A: Finness modulus is the sum of cumulative percentage retained on each seive divided by 100.…

Q: Based on the sieve analysis a soil has % finer for the following sieves: No. 10- 84% ; No. 40- 71%…

Q: For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL= 32. Classify the…

Concept explainers

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.

Question

5.3 Classify the following soils by the AASHTO classification system. Give the group
index for each soil.
Sieve analysis-
Percent finer
Liquid
limit
Plasticity
index
Soil
No. 10
No. 40
No. 200
98
80
72
52
21
90
74
58
38
12
84
71
64
41
14
100
78
82
32
80
68
48
30
11
ABCDE

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which state describes soil that does not show cracks when deformed (choose correct state that applies). A) Plastic state B) Liquid State C) Semisolid state D) Solid state
the advantage of the is to ensure the compaction of the soil within 10 points the actual mold size. sieve No. 4 collar drying oven O hammer
DATA AND RESULTS: SOLVE FOR ITS FINENESS MODULUS AND % ORGANICMATTER SIEVE SIZE WT. RETAINED % WT. RETAINED CUMULATIVE % OF RETAINED #4 #8 33.3 # 16 97.7 # 30 620 #50 95.7 # 100 27.9 PAN 31.5
3-Specific gravity of the soil solids is useful in the determination of void-ratio, degree of saturation, how? Find the relation?
1. ument size? yeability2 3. What factors affect porosity and permeability?
I need the answer quickly
659, The Lexington Sand and Gravel Company has made a bid to supply sand for Laramie's new sand filter. The request for bids stipulated that the sand have an effective size in the range 0.35 to 0.55 mm and a uniformity coef- ficient in the range 1.3 to 1.7. Lexington supplied the following sieve analysis (sample size = 500.00 g) as evidence that its sand will meet the
- Once answered correctly will UPVOTE!!
Describe the various ways of Testing for Dispersive Clays.
need asap :(
Outline the plasticity chart by placing its borders for the classification of fine particle soils