Ethylene (C₂H4) enters an adiabatic combustion chamber at 25 °C, 1 atm and is burned with 40% excess air that enters at 25 °C, 1 atm. The combustion is complete and the products leave the combustion chamber at 1 atm. Assume To -25 °C Part A Determine the temperature (T) of the products. Express your answer to four significant figures. Submit Request Answer ▼Part B Determine the entropy generation (Sigma). Express your answer to five significant figures. Submit Request Answer Part C Determine the irreversibility. Express your answer to alx significant figures. Submit Request Answer ? ? ? K kmol-K kmol

Q: Using Fig. 6.10: (a) Determine whether ice that forms at P =700 MPa floats or sinks in the liquid…

A: Consider the pressure of water is 700 MPa. The phase diagram of pure substance is provided between…

Q: Calculate the enthalpy and entropy of liquid isobutane at T = 160 o F and pressure P = 1000 psia.…

A: To find:The enthalpy and entropy of liquid isobutane at T=160oF and pressure P=1000 psia.Given:The…

Q: Superheated steam at 900 K and 9.0 MPa (stream 1) is blended with saturated steam at 3.0 MPa(stream…

A: The objective of the question is to find the temperature of stream 2 (T2) and the mass ratio of…

Q: Use the data in the steam tables to answer thefollowing:A. Find the change in internal energy when…

A: Solving first 3)

Q: A ball at 1200K is allowed to cool down in air at an ambient temperature of 300K. Assuming heat is…

A: Since you asked to solve this question by Runge-Kutta of fourth-order which is a lengthy process…

Q: A 1g cube of metal A at 80 °C is placed in 100 cm³ of water and causes a 0.333 °C rise in water…

A: For metal A: Given, mass of the metal A, mA = 1 g The initial temperature of the metal, TA,0 = 80 °C…

Q: 6. Which of the following is true of equilibrium: a) there is no heat flow between two bodies in…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: . There is a very hot (600 °C) stream of oil exiting a reactor at 100 3. 1 kg/min that must be…

A: Initial oil temperature, Toil(1) = 600°C = 873 K Initial water temperature, Twater(1) = 75°F =…

Q: During the power stroke in a four-stroke automobile engine, the piston is forced down as the mixture…

A: Given data: Engine is running at 3000cycles/min Gauge pressure before expansion=18.75atm Initial…

Q: Cooling a Gas Mixture. It is required to cool a gas mixture composed of 75 mol % N₂, 15 mol% CO₂ and…

A: A mixture of gases is cooled in a heat exchanger.

Q: - You are heating motor oil to make it flow better from the original shipping container to the new…

A:

Q: Steam is used to cool a polymer reaction. The steam in the steam chest of the apparatus is found to…

A: The initial state of the steam is at a temperature of 250.5°C and a pressure of 4000 kPa. The final…

Q: A. Show that dp Determine the final density and enthalpy of the water: P (a) if it is heated to 50°C…

A: Initial conditions are given as, Also,

Q: After a tough week of exams, you decide that nothing could be better than having a home cooked roast…

A: Thermal diffusivity: In heat transfer, thermal diffusivity is the thermal conductivity divided by…

Q: Methane (CH4) at 298 K, 1 atm enters a furnace operating at steady state and burns completely with…

A: Write the reaction for the combustion of methane as follows: CH4 + 2O2  →CO2 + 2H2O   One mole of…

Q: starting with the chocked mass flow rate equation for isothermal ideal gas flow discharging through…

A: The mass flow rate of the orifice is considered to be equation one. The coefficient of discharge…

Q: Two streams are mixed in an adiabatic mixer, as shown in the figure. It is known that: • Stream 1 is…

A: A stream of mixture of liquid and vapor is mixed with superheated water vapor adiabatically.