estimate the triple point temperature and pressure frome slope

Q: Which of the following variables is not needed to calculate for the surface tension of a liquid…

A: The explanation is given below-

Q: Consider the following data for xenon: Triple point: -121°C, 280 torr Normal melting point: -112°C…

A: Triple point: —121°C, 280 torr Normal melting point: —112°C Normal boiling point: —107°C

Q: Describe the type of information you would look for when given a chemical formula in order to…

A: (a) According to the question - These are the  information when given a chemical formula in order to…

Q: Using the Clausius-Clapeyron equation to examine the relationship between vapor pressure and…

A: The relationship between vapor pressure and temperature should be given using Clausius-Clapeyron…

Q: Define these properties and explain the relationship of IMF strength to each property. (a) Boiling…

A: (a) Boiling point Boiling point is the point where a matter changes its state from liquid to gas.…

Q: Which of the following correctly represents the sequential change in mechanical state with…

A: Introduction :  Amorphous Polymer : In the amorphous polymer the molecules are arranged randomly and…

Q: If a particular liquid has a normal boiling point of 338.0 K and a vapor pressure of 75.0 mmHg at…

A: Given, Note: vapour pressure at normal boiling point = 1 atm Vapour pressure (P): P1 = 1 atm = 760.0…

Q: As the effective number of atoms increases in any of the cubic structure, the co-ordination number…

A: The effective number of atoms in a cubic crystal and coordination number are proportional to each…

Q: Which of the following forces results from a temporary dipole (instantaneous dipole)? Group of…

A: A multiple choice question based on intermolecular forces, which is to be accomplished.

Q: truo or false

A: Strain is defined as "deformation of a solid due to stress". Note that strain is a dimensionless…

Q: Linear molecules must be nonpolar, thus linear molecules cannot participate in dipole dipole…

A:

Q: The drop size of polar liquids was larger than the drop size for the nonpolar liqulds. O True O…

A: Polar liquid have strong interaction between them, so the liquid size will decrease as the force is…

Q: the choices are: (1): weak or strong (2): dipole-dipole dipole-induced dipole ion-dipole ion-reduced…

A: Answer: 1) The low solubility of CH3CH2CH2CH2CH2OH in water. In that the Hydrogen bonding…

Q: As the temperature of a pure substance is decreased at constant pressure, all of the following are…

A: Answer:Matter can be divided into 3 physical states:SolidLiquidGas

Q: Calculate the percentage of empty space in a face-centered cubic cell. Need to show all your…

A: The packing efficiency is defined as the total volume occupied by the atoms in an unit cell.  In…

Q: All of the following properties tend to increase with stronger intermolecular forces except...…

A: 1. Intermolecular  force is the force which bond molecule together.

Q: Consider the effect of intermolecular forces on the vapor pressure (vp), boiling point (bp), and…

A: As the strength of intermolecular forces decreases. What  effects occur on the  Changing vapor…

Q: 2. Sketch within a cubic unit cell the following planes. (a) (0T) (b) (1 0 2) (e) (T 1 ī) (d)23) (e)…

A:

Q: Which of the properties below is incrorrect for a solid? - diffusion occurs extremely slowly -…

A: The movement of particles from high concentration region to low concentration region is known as…

Q: TRUE OR FALSE Melting Point should be taken on dry solids only.

A: Yes it is true melting point should be taken of dry solid only . because if  it contains moisture…

Q: A molecule will demonstrate hydrogen bonding if and only if it has a hydrogen atom directly bonded…

A:

Q: On what factor does the boiling point of the liquid depends?

A: Given: Factors affecting boiling point.

Q: Topic : PHASE e) What is difference between the triple point and critical point explain with…

A: Part e :-  Triple point :- In phase diagram it is defined as the point of particular temperature and…

Q: An unknown substance has a density of 4.56 g/cm3 and atomic radius of 0.190 nm. It crystallizes to…

A: The length of the edge of the BCC unit cell and the density of the lattice is given by: Where n is…

Q: Label the features of the phase diagram. Pressure (not to scale) liquid-gas equilibrium triple point…

A: Phase diagram is a graphical representation of the physical states of a substance under different…

Q: What is the definitions of the normal boiling point? Why is it necessary to specify the atmospheric…

A: Normal boiling point and boiling point this are the physical properties of liquid State of matter .…

Q: If you were given an unknown solid substance , how could, you determine its boiling point if it is a…

A: The boiling point of a substance is defined as the temperature at which the vapor pressure of the…

Q: indicate the Miller Bravais indices for simple cubic directions

A: In crystallography, Miller indices are used as a notation system by which the planes of a Bravais…

Q: centripetal force

A: A centripetal force is defined as a force which keeps the body to be in the circular path.

Q: 41. The graph of boiling point against hydrides of Giroup 14.15.16,!7 (Group IV. V. VI. VII) reveals…

A: The boiling point of hydrides of group 14 increases down the group due to increase in vanderwaal…

Q: A substance is nearly nonviscous and quite compressible,and it has a large coefficient of thermal…

A: States of matter- There are three states of matter-solid, liquid and gas. Solid- in solids particles…

Q: Directions: Use the following terms to fill-in the blanks. The terms may be used more than once. Gas…

A:

Q: by James Joy... TEST: Bondin.. Grade 10 Ble.. Post Attende. Major Conce. Copy of Nikki.e Request…

A: The substance with high boiling point have the strong intermolecular forces.

Q: How many phases are present at each of the points a–d indicated in attachement

A: To determine the number of phases present at each of the point a, b, c and d of the below phase…

Q: Which is true about metallic solids? O They usually have low density. They are poor thermal and…

A: In this question, we have to identify true and false for both the questions.

Q: Is silicon tetrafluoride dispersion force, hydrogen bonding, or the pole interaction

A:

Q: what is expected it to take more or less energy to promote of solid propanone to liquid propanone at…

A: Standard data: The latent heat of fusion of propanone = 5.7 kJ/mol The heat of vaporization of…

Q: Give correct detailed Solution with explanation needed of all sub parts....don't give Handwritten…

A: Since you have posted a question with multiple sub-parts, we will provide the solution only for the…

Q: Please help me answering this just answer molecular solids

A: Molecular solids: These are the solids that are just formed by interconnected molecules. It can be…

Q: Which point defect in crystals of a solid does not change the density of the solid?

A: The missing of atoms or ions in an ideal or imaginary crystal structure or lattice and the…

Crystallography

Crystallography is the category of science that focuses on the atomic and molecular arrangements with their bonding constituting the crystal structure. It is derived experimentally and originated in the year 1912. It is a combination of two words; those are crystal, meaning a cold drop, and graph, meaning writing.