Estimate power for aunealed low carrbon steel strip 20mm wide adomm thck, dolled to a tuickhess of 6mm. the roll radius es 200mm e the noll roteate 200geu/min coefficient aeuter face =041 1o car bon steel Such as A 020 has use 4 riction ae the olee ueozk K=530M pa and

Q: What are the two most common systems of units?

A: Given Data⇒ systems of units Problem statement⇒ Problem says What are the two most common systems of…

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: TC Sin2 * cos' z 2. sin? dx

A:

Q: part1 and part 2 are correct

A: Process 3-4s : Isentropic expansion process.Process 3-4a : Actual expansion process.Process 4a-1 :…

Q: y' = -y tan x, y(0) = 2

A:

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the…

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the…

A:

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: Answer in number 7 and 8.

A:

Q: The triangular lamina with base = 80 mm, height = 60 mm.  The Iyy value is _____________ mm4 Select…

A: Given data: base (b) = 80 mm height (h) = 60 mm Need to determine the moment of inertia about y-y…

Q: Members ABC and DEF are joined with steel links (E = 200 GPa). Each of the link is made of a pair of…

A:

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: Where did the 0.10472 rad/s come from?

A:

Q: To measure the angles, engineer square is used. Select one: True False

A:

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: The equation of the unit circle is _______________.

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: 200 mm В

A:

Q: what is part number 4

A: Solution:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: how can I get the 85 α

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.