Estimate and plot the vertical stress increase, Aoz, along verticals through A, B, the centerline, C and D of the embankment at depths of 0 ft, 10 ft, 20 ft, 30 ft, 40 ft and 50 ft below the original ground surface. Plot also the variation of Aoz along horizontal planes at similar depths. Assume y = 120 pcf. 25ft A * B £ * с D 15ft TEIN

Estimate and plot the vertical stress increase, Aoz, along verticals through A, B, the centerline, C and D of the embankment at depths of 0 ft, 10 ft, 20 ft, 30 ft, 40 ft and 50 ft below the original ground surface. Plot also the variation of Aoz along horizontal planes at similar depths. Assume y = 120 pcf. 25ft A * B £ * с D 15ft TEIN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.) A house is being built on the soil profile shown below bears at the depth shown. The surface loading created by the house is 1500 psf. Draw the o, o', u, profiles with depth and show values at depth shown. In addition, calculate the load on the basement wall with Ko = 0.35. Depth (ft) Sand Ya = 110 pcf Y = 116 pcf 7 ft 10 Clay = 119 pcf 40 Sand = 118 pcf
plase help question is clear please dont other answer for question A flexible rectangular area is subjected to a uniformly distributed load of q = 225 kN/m². Determine the increase in vertical stress, Aoz at a depth of z = 2 m at Point A. %3D 0.5 m 1m 0.5 m 1 m Point A
QUESTION 2 A rectangular footing 1000 x 2000 mm shown below is subjected to a vertical point load of 600 kN acting at eccentricities ex = 200 mm and eyy = 100 mm, as show on the Figure below. Calculate the stresses at the corners A and D, and sketch the stress distribution along the face A-D. е 200 mm Vertical force = 600 kN B eyy =100 mm 1 m D. 2m Rectangular footing - Plane
determine the tensile development lengths required using: (a) ACI Metric Equation 25.4.2.3a, assuming Ktr = 0, and (b) ACI Metric Equation 25.4.2.3a and the computed value of Ktr . Use fy = 420 MPa and fc′ = 28 MPa.
Q#4: Plate load test performed on a uniform deposit of sand and the following observations were recorded. The size of the plate was 45cm x 45cm. Plot the Pressure-Settlement Curve and determine the safe load on a footing 2m x 2m if the settlement is not to exceed 40mm. Pressure (kPa) 2 4 8 12 16 24 Settlement (mm) 3 6 20 40 60 100 Note: Write the proper answer in word format Subject: Geotechnical Design
The following results were obtained from CU tests on a clay soil that is the foundation material for an embankment. 03 (kPa) 300 400 600 0₁-03 (kPa) 331 420 487 Au (kPa) 111 160 322 (a) Determine the total and effective principal stresses for all three tests (You may summarize them in a table). (b) Recommend the shear strength parameters to be used for short-term and long-term analyses. The maximum confining pressure (cell pressure) at the depth of interest is 300 kPa. (Note: the clay is a normally consolidated one).
The location of trial failure surface on a slope is shown in Figure and the stress components for each slice are listed in Table. Slice Shearing component _(kN.m·') -0.280 -0.227 0.383 3.214 6.543 8.368 9.792 Normal component (kŇ.m*) 1.911 7.745 13.139 16.344 17.625 16.718 12.125 0.486 Length of trial failure surface=11m Soil friction angle 6° Cohesion, c=28kPa No. 1 3 4 6. 4.228 Trial Fallure Surface (a) Compute the driving stress. (b) Compute the stabilizing stress. (c) Analyze the safety of the slope.
The soil profile at a road construction site is as shown in figure (not to scale). A large embankment is to be constructed at the site. The ground water table (GWT) is located at the surface of the clay layers, and the capillary rise in the sandy soil is negligible. The effective stress at the middle of the clay layer after the application of the embankment loading is 180 kN/m². Take unit weight of water, Yw = 9.81 kN/m3. Embankment load boudi Sand GWT 2m y = 18.5 kN° it enit Clay Specific gravity, G̟ = 2.65 Water content, w = 45% Compession index, C. = 0.25 6m %3D %3D Impermeable layer The primary consolidation settlement (in m, round off to two decimal places) of the clay layer resulting from this loading will be
A square footing is loaded as shown in Figure 05.13. The center of the base of footing is at coordinate (0, 0, 0). Determine the increase in vertical stress at a point whose coordinate is (3, 0, 4) using pressure isobars based on Boussinesq equation for square footings shown in Figure 05.7. O O O 10.215 O 10.512 10.125 10.251 P = 900 KN #7 2 m Figure 05.13
A soil profile is shown in Figure ?-?. Compute the shear strength on the horizontal plane at point ?, and on the vertical plane at point ?.
Wooden posts (E=1,800,000 psi) are used for a retaining wall, each post is 6in x 6in. If the soil pressure along a post varies linearly from zero at A to a maximum at B, determine the displacement at the top of the post. Assume B is fixed and A is free. Report your answer in inches to three decimal places.
Calculate: a.) The unit weight of soil at a depth of 3m below the ground surface. b.) The normal stress of soil at a depth of 3m below the ground surface. c.) The potential shear strength of the soil at a depth of 3m below the ground surface when the water table is at a depth of 3.5m and the soil is cohesionless. d.) The modified value of the shear strength if the water table reaches the ground surface. e.) The modified value of the shear strength if the water table reaches the ground surface but the soil has a cohesion of 12 kPa.