Establish the reasons of being similar of two turbomachines and Explain the significances c coefficients used in the turbomachinery?

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: Illustrate the correct sequence of the Theory of Accidents by Heinrich? A. B. C. O D. Social…

A: Heinrich's Domino Theory states that accidents result from a chain of sequential events,…

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: How is spindle aligmment done in a milling machine?

A: By spinning a cutting tool (cutter) and sliding it into the work item, a milling machine removes…

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: Construct a Main Schedule of the machine tool of your choice?

A: The machine tool should have preventive maintenance . it is an essential thing for the properly and…

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: Apply Mason Rule (S&P) to block diegron below. кле (бар) то e(s) Git H₂P G Hs H₂ ((s) H₁ 62 H₁ бу…

A:

Q: Solve for the mobility.

A:

Q: raw kinematic diagram of the drawing mechanism. etermine degrees-of-freedom of the drawing…

A:

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: I have a cube fixture. Made from 6061-T6. Length is 12 inches, width is 12 inches, and height is 2…

A: Calculating the overturning moment of a static object placed on a flat surface, like your cube…

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: A projectile is fired with an initial velocity of 200 ft/s upward at an angle of 30° with the…

A: Initial velocity = 200 ft/s Angle = 30o Distance = 257.6 ft

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 3.17 g coins…

A:

Q: Analytically determine the maximum linear displacement of the cutting blade .75 S0 crank blade Your…

A:

Q: Determine the following for point C on the slide if the angle theta measures 45 degrees and the BC…

A:

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: Find Ixx for the given Plane, where b1 =160m, d1=25m, b2=20m, d2=90m, b3=60m & d3=25 m (Enter only…

A: Given data:-b1=160m, d1=25m, b2=20m, d2=90m, b3=60m, d3=25mArea of section 1, A1=160×25=4000m2Area…

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: True

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: solve the following exercises:

A: To determine the acceleration of the system

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: Disadvantage of taper turning by taper turning attachment method is that only limited taper angles…

A:

Q: Draw the following spring with all mensions in sheet (write down all the equations you used in the

A:

Q: Find the oxthagonal r-6a.Cose whese a is pasametes

A: r=6acosθWhere a is a parameter Now need to calculate orthogonal trajectory

Q: QUESTION 1 Calculate the spindle speed in RPM of a lathe turning a 96 milimeter diameter material…

A: Given:d=96 mmV=148 SMPM

Q: 1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three questions.…

Q: Please calculate the moment of inertia values for each figures according to defined rotation axises.

A: Given Data: The radius of the sphere is R. The length of the rod is L. The masses of the sphere and…

Q: Calculate the mechanical advantage of the following compound machine.

A:

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, ps=15°.

A:

Q: 'oint C has a velocity of 12in/sec in the direction hown., and point B has a velocity of 10.4…

A:

Q: Gentlemen, please help to solve a,b,c as I faced confusing questions about screw jack. Conditions…

A: Given: The load to be lift, M = 3.2 ton = 3200 kg The screw pitch, d = 12 mm The diameter of screw…

Q: mm/revolution is the unit of O a. Feed O b. Spindle speed O c. Cutting speed O d. Depth of cut

A: We have to solve unit conversation

Q: In a shaper machine, the crank rotates at constant speed of 130 r.p.m. The angle travelled by the…

A: Given that :           A shaper machine           Crank rotating at speed (N) = 130 rpm…

Q: b) Calculate the inclined angle and orthogonal rake angle yo, when yx =10°, yy =8°, qs=15°.

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.