er toward the next spanning up to 36 m. The girders have built-up cross-sections as show ure. It is estimated that the girder construction load can be considered as a uniformly distribu th 4.0 kN/m intensity. This includes the self-weight of the girders. What is the maximum ess in a girder during construction?

er toward the next spanning up to 36 m. The girders have built-up cross-sections as show ure. It is estimated that the girder construction load can be considered as a uniformly distribu th 4.0 kN/m intensity. This includes the self-weight of the girders. What is the maximum ess in a girder during construction?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve with explanation please
Solve for set B.
Design the slab reinforcement if the maximum positive moment is Mup= wul2/11 and the maximum negative moment is Mun= wul2/10. Given: Superimposed dead load = 4.76 kPa Live Load = 1.9 kPa Weight of slab = 3.45 kPa Length = 10.9 m Span = 3m
A simply supported prestressed concrete beam is of 25m span. The initial stress is 1000 MPA. The slip in the jack during tensioning has been 2mm. If Es = 200 GPa, the loss of prestress due to anchorage slip is
The section of a Super-T prestressed concrete girder is shown below. The girder is simply supported on a span of 7.0 m and are pre-tensioned with total initial force of 825 kN from low-relaxation strands. The girder supports a total dead load of 2 kPa and live load of 6 kPa. There is a loss of prestress of 0.2 at service loads. Assume "-" for compression and "+" for tension. Hint: Assume tributary width is equal to flange width. Properties of the section: A = 100,000 mm2 INA = 940 x 106 mm4 All measurements in the drawings are in millimeters. 1. What is the stress, in MPa, at the top fibers of the girder at end span due to initial prestressing force only? 2. What is the stress, in MPa, at the bottom fibers of the girder at midspan due to initial prestressing force only? 3. What is the stress, in MPa, at the top fibers of the girder at end span due to prestressing force and service loads? 4. What is the stress, in MPa, at the bottom fibers of the girder at midspan due to prestressing…
solve for the wind load on the right side
3. A doubly reinforced beam has dimension of 300mmw x 600mmh. It is reinforced with 225mm diam compression bars and 4 25mm diam tension bars. Concrete cover from centroid of steel bar is 60mm. On its section has a bending moment of 300KN-m. Using working stress design method what are the stresses acting on the concrete, compressive and tensile steel bars? N3D8
solve the wind load on the left side
Determine end reactions for Beam B-1 and Girder G-1. B-1 1 F1 • L1= 24 ft L2= 6 ft Live load 30 psf 4" Thick concrete slab (density = 150 pcf) . 5/8" Thick terrazzo (12 lb/ft2/in) • Beam weight = 35 lb/ft . Girder weight = 26 lb/ft Please round to the nearest one. One end reaction for B-1 = lbs One end reaction for G-1 = lbs Please answer all parts of the question. 20 DOO 000 F2 @ 2 JAL #3 G-1 F3 54 $ F4 % 5 F5 L2 L2 L2 L2 MacBook Air F6 A 6 & 7 F7 11 ► 11 * 8 F8 F9
A prestressed beam has a width of 300 mm and depth of 600 mm. It is subjected to a bonded prestress tendon having an area of 590 mm2 acting at a distance 550 mm from the compression, face of the member. fc' = 34.6 MPa, fpu = 1860 MPa, fpy = 0.85fpu (stress-relived strands).COMPUTE THE STRESS IN THE PRESTRESS REINFORCEMENT AT NOMINAL STRENGTH (MPa)
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored liveload in Kilo Pascals? Express your answer in 2 decimal places
Please asap