Equations: F₁=M S F₁ = 3V 2A M=WL² 8 M=Pa V=WL² 2 Calculate the Maximum Shear & Moment 1. What is the minimum cross-sectional area and section modulus for the beam below. HINT: Draw Shear & Moment diagram When load is symmetrical, equations for multiple conditions can be used & added together to determine shear & moment. F= 750 psi F= 175 psi 800 12'-0" 800 300 plf

Equations: F₁=M S F₁ = 3V 2A M=WL² 8 M=Pa V=WL² 2 Calculate the Maximum Shear & Moment 1. What is the minimum cross-sectional area and section modulus for the beam below. HINT: Draw Shear & Moment diagram When load is symmetrical, equations for multiple conditions can be used & added together to determine shear & moment. F= 750 psi F= 175 psi 800 12'-0" 800 300 plf

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

* 10k 8' x 8' lok * L=24' 81 lok lok 8⁰ Figure (a) 8' w=2k/ft - 8 (2) Design the beam shown in Figure (a), (check the bending, shear, and deflection) use the allowable deflection as 0.4 in.
Show FBD, all the step by step solution and neat handwritten.
A wooden beam is fabricated by nailing together three pieces of dimension lumber as shown. The cross-sectional dimensions of the beam are also shown. The centroid is 3.4 in. below the top surface of the beam, and the moment of inertia about the z axis is 230.9 in.4. The beam must support an internal shear force of V = 365 Ib. If each nail can provide 120 Ib of horizontal resistance, determine the maximum spacing sfor the nails. 2 in. 4 in. 2 in. 2 in. 8 in. O 4.86 in. 8.32 in. O 7.91 in. 9.36 in. O 5.59 in.
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
anwser part 4
Remember to show all units and provide a step by step solution showing all work. Draw and label diagrams.Use the formula sheet.
A structural T-section is formed by connecting a 150 mm x 40 mm steel plate with a 80 mm x 40 mm steel plate as show in the diagram. For the combined section calculate: 150 mm 40 mm A 40 mm 80 mm SSESSM a. the location "e" of the principal (centroid) X-axis (relative to the top edge of the section). "c b. the second moments of area Ixx and Ivy about the principal X- and Y-axes.
イ H.W.pdf -> A simplified model as shown in figure below of a planur robotie urm. You may ussue thut each segment has length 1.5 m, aad the applied force is 250 N. 0, = 35 and -0,- 20. Calculate dhe aoncnt that the force, F. cacits about dhe point A ...
Based on the figure below. Determine the required value of L if the force in member CE is equal to 891 N tension.
02) The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmax = 1936x(0.5). 2. IfG =30 GPa find the angle of twist at the free end of beam. Y 10 kN 25 NA 120 mm 15 500 mm Good Luck and be Green