Engine oil at 60ºC (μ = 0.07399 kg/m s, ρ = 864 kg/m3) flows in a 8-cm-diameter tube with a velocity of 2.2 m/s. Determine (a) the friction factor and (b) pressure drop along a fully developed 6-m long section of the tube

Q: Consider a pipe carrying water at a temperature of 60°F. The pipe diameter is 4 inches and the water…

A:

Q: Problem 3 The Flame Consulting Company (FCC) is designing an experiment where the average velocity…

A: Given:Velocity profiles:Laminar flow, uVc=1-rR2Turbulent flow, uVc=1-rR1/nFind:The radial location…

Q: Resolving of Example (1-3) Two reservoirs with a difference in elevation of 15 m are connected by…

A: Length and diameter of the pipes:-Pipe 1:- Length (L1  ) = 300 m, Diameter (D1) = 0.3 mPipe 2:-…

Q: ty of 3.5 m/s. Determine the pressure drop per 10 m of the pipe. What is minor loss in pipe flow?…

A: given:density ρ=1252kg/m3μ=0.27kg/m.sdiameter D=6cm

Q: HW Pressure Drop in a Pipe Water at 60°C is flowing by pump in a 0.0015-m-diameter 0.5-m-long pipe…

A: Given: T= 60o C Pipe diameter, d=0.0015 m length of the pipe, L=0.5 m average velocity, v=0.5 m/s…

Q: Heated air at 1 atm and 30∘∘C is to be transported in a 150-m-long circular plastic duct at a rate…

A:

Q: oss in turbulent flow in a pipe (a) varies directly as velocity  (b) varies inversely as square of…

A:

Q: A7 To a 5ft long ½” ID pipe that is maintained at a uniform temperature of 150ºF oil enters at 70ºF…

A: Given: The diameter of the pipe, d = ½ in  = 0.04166 ft The length of the pipe, L = 5 ft The…

Q: Heated air at 1 atm and 35°C (p= 1.145 kg/m' and u= 1.895 X10$ kg/m s )is to be transported in a…

A: Calculated the minimum diameter of the duct.

Q: Consider the flow of oil with p = 870 kg/m² and u = 1.03 kg/m-s in a 3-cm-diameter, 1.5-m-long…

A: Given data:  density, ρ=870 kg/m3 dynamic viscosity, μ=1.03 kg/m-s diameter, d = 3 m = 0.03 m…

Q: water at 4-degree centigrade ( ρ=998 kg/m3 and μ=1.52 *10-3pa.s) is flowing steadily through a 3mm…

A: Given data:

Q: Consider laminar flow of water in a 0.85-cm-diameter pipe at a rate of 1.15 L/min. The velocity…

A:

Q: Glycerin, with a density of 1260 kg/m3 and an absolute viscosity of 1.5 kg/m.s, flows in a tube with…

A:

Q: Required Information x Water at 10°C (p = 999.7 kg/m³ and µ=1.307 × 103 kg/m-s) is flowing steadily…

A:

Q: Water at 60°F (? = 62.36 lbm/ft3 and ? = 7.536 × 10−4 lbm/ft·s) is flowing steadily in a…

A: Given data: Discharge, Q = 0.2 ft3/s Diameter of pipe, d = 2 in. = 0.167 ft Length of the pipe, L =…

Q: Consider the flow of oil with p = 870.15 kg/m³ and µ = 3.93 kg/m•s in %3D a 37.6 cm-diameter…

A:

Q: In fully developed laminar flow in a circular pipe, the velocity at R/2 (midway between the wall…

A: Given data as per the question the velocity at R/2 = 11 m/s

Q: Air at 1 atm and 40C flows in a 8-cm-diameter pipe at a rate of 2500 L/min. The friction factor…

A: Given data:The flow rate is Q = 2500 L/min.Diameter of the Pipe d=8cmThe friction factor is f =…

Q: Q1 What is the Reynolds number? How is it defined for (a) flow in a circular pipe and (b) flow over…

A: This question is based on the concept of fluid mechanics.

Q: Air with ρ = 1,202 kg/m3 and ν =15.1 x 10-6 m2/s, is flowing steadily in a duct shown in Figure 1…

A:

Q: How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in…

A: Write the hydrodynamic entry length for the flow in a pipe.

Q: What is turbulent viscosity? What causes it?

A: Turbulent viscosity is defined as the coefficient of viscosity whose value obtained the average…

Q: Petrol of specific gravity 0.85 is to be pumped through a 1.2 km pipeline to a petrol  station. The…

A: Given: The specific gravity of fluid, γ = 0.85 The length of the pipe, L = 1.2 km = 1200 m The…

Q: Consider laminar flow of water in a 0.9-cm-diameter pipe at a rate of 1.15 L/min. The velocity (m/s)…

A: we got  d=0.009m Q=2.9167×10^-5 m^3/sec

Q: A vented tanker is to be filled with fuel oil with Density= 920 kg/m3 and Viscosity =0.045 kg/m s…

A:

Q: Show that during steady and incompressible flow of a fluid in an adiabatic flow section (a) the…

A: Steady and incompressible flow through the adiabatic section, the effects of friction on temperature…

Q: Determine (a) the head loss, (b) the pressure drop, and (c) the pumping power for water flowing…

A:

Q: Heated air at 1 atm and 35°C (p= 1.145 kg/m' and u= 1.895 X10$ kg/m s )is to be transported in a…

A: Given Data The pressure of the air is P=1 atm.  The temperature of the air is T=35°C. The discharge…

Q: Heated air at 1 atm and 35°C is to be transported in a 150-m-long circular plastic duct at a rate of…

A: Given: The flow rate of the circular plastic duct is Q=0.35 m3/s and the head loss in the pipe is…

Q: ter is flowing fully turbulent in a straight galvanized iron pipe with a cross- sectional area of…

A: Given:A=1.963*10-3 m2