Q3 Glycerin at 40°C with density of 1252 kg/m³ and viscosity of 0.27 kg/m.s is flowing through a 5-cm-diameter horizontal pipe made of stainless steel with a mean velocity of 4 m/s. Determine the pressure drop per 10 m of the pipe and the required pumping power. What will be the required pumping power if the fluid changed to air.

Q3 Glycerin at 40°C with density of 1252 kg/m³ and viscosity of 0.27 kg/m.s is flowing through a 5-cm-diameter horizontal pipe made of stainless steel with a mean velocity of 4 m/s. Determine the pressure drop per 10 m of the pipe and the required pumping power. What will be the required pumping power if the fluid changed to air.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermo-Fluid
Water is flowing in a pipe with radius of 30 cm at a velocity of 12 m/s. The density and viscosity of water are as follows; Density 1000 kg/m² ; Viscosity = 1.12 Pa s, What is the Reynolds number? * 5812 O 5316 O 4912 O 6428
Question 2A large vat contains water, which contains a drainage pipe at a height h1, as shown infigure 2. The drainage pipe has a length L. = 0.4 m, and a radius R = 15 mm, and releaseswater to the atmosphere at a flow rate Q. The connection between the pipe and the vatwall has a loss coefficient of KL = 0.8.Point A is in the middle of the tank at a height, hi.You can assume that the flow in the drainage pipe is fully developed and laminar. The density of water is p = 1000 kg/m° and the viscosity is u = 1 mPa.s. The acceleration due to gravity is 9.81 m/s? a) Find an expression for the pressure at point A.b) Find an expression in terms of Q, L, d, K, p and u for the pressure losses along the pipe (including the losses at the inlet and exit).c) If the flowrate out of the drainage tank is Q = 50 L/min, find ho. You may assumeany change of ho with time is negligible.
Water enters a piping system with a diameter of 0.1016 m from a reservoir with a volumetric flow rate of 0.1893 m³/min. Determine whether the flow is laminar or turbulent if, during the winter, the dynamic viscosities of μ = 1.308x 10-3 Pa 's and 0.687x10-3 Pa s during the summer. What is the length of pipe necessary to reach a fully developed flow?
Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20 °C to 60 °C. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. a) Determine the Reynolds number b) What is the thermal coefficient on question number c) what is the heat absorbed by the water?
Asap write correct solution
Blue and yellow streams of paint (each with a density of 1.6 slugs/ft³ and a viscosity 1500 times greater than water) enter a pipe with an average velocity of 9 ft/s as shown in the figure below. Would you expect the paint to exit the pipe as green paint or separate streams of blue and yellow paint? Explain. Repeat the problem if the paint were "thinned" so that it is only 10 times more viscous than water. Assume the density remains the same, and the temperature is 60°F. Classify the flow. Splitter Laminar Yellow Blue Laminar flow has mixing only by molecular diffusion. Turbulent flow has mixing due to large scale fluctuations. Reynolds number is a measure of whether flow is laminar or turbulent. Classification of viscous flow as laminar or turbulent dictates how the flow is analyzed. What is the Reynolds number for the flow with a viscosity 1500 times that of water? Re= 2 in. What is the entrance length for this Reynolds number? le= ft Green? 25 ft
Heated air at 1 atm and 100°F is to be transported in a 900-ft-long circular section plastic duct at a rate of 1.4 lb/s. I want to determine the head loss and pumping power at the three diameter values in the table below. Complete the table to help me choose a wise diameter. Why would a good design not only focus on minimizing the pumping power? Diameter Head loss, hi Pumping power, W Reynolds number, Re n.d. f n.d. (in) ft hp 8 12 16
At a speed of 0.2 m/s, light oil with a density of 880kg/m and a viscosity of 2.1cP is pumped from a huge oil tanker to a power plant's storage tank. The discharge point is 50m above the liquid level in the tanker, at the top of the storage tank. The pipeline is a 150mm smooth pipe with six typical 90° elbows and two gate valves that is 200 meters long (fully open). The atmosphere is vented from both the oil tanker and the storage tank. a. Calculate the pressure drop in J/kg along the pipeline. b. Calculate the pumping power (in kW) if the pump-motor set has a 65 percent efficiency.
Please help me