Engine oil enters a circular tube D=6-cm in diameter and L=29-m in length. If the flow rate and inlet temperature of the oil are 0.3-kg/s and Tmi =20°C, find the thermal entry length (x, =?) in the tube? Note: Use the following properties at mean temperature of the engine oil. u=0.50 N.s/m², v = 1.1 x 10-' m² /s, Pr = 220

Engine oil enters a circular tube D=6-cm in diameter and L=29-m in length. If the flow rate and inlet temperature of the oil are 0.3-kg/s and Tmi =20°C, find the thermal entry length (x, =?) in the tube? Note: Use the following properties at mean temperature of the engine oil. u=0.50 N.s/m², v = 1.1 x 10-' m² /s, Pr = 220

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QI/An electronic device is cooled by water flowing through capillary holes drilled in the casing. The temperature of the device casing is constant at 353 K. The capillary holes are 0.3m long and 2.54x10m in diameter. If water enters at a temperature of 333 K and flows at a velocity of 0.2 m/s, calculate the outlet temperature of the water.
Water flows along a tube of diameter d = 6 mm with a velocity w = 0.4 m/s. The temperature of the tube wall t = 50°C. What should the length of the tube be to ensure a water outlet temperature tr2 = 20°C at a water inlet temperature twi = 10°C?
What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 2 inches? The viscocity is 1.358 x 10^-5 lb/ft-s and the mass flow rate is 73 lb/h.
Water flow in steel pipe at a temperature of 50o C as shown in the figure. The pipe is wrapped with thermal isolation. Air is flowing over the pipe at a temperature of -5o C and a speed of 3 m/sec. It is known that 1kWh costs 0.05$ Find the daily cost of the heat losses per meter without the pipe isolation? What is the daily cost saving when using the isolation?
Air flows from a 10cm pipe in which the temperature and pressure are 4-C and 280kpa, respectively, into a 5cm pipe in which the pressure is 147kpa gage. Calculate the velocity and discharge in each pipe, assuming isothermal conditions, standard atmospheric pressure and no losses. The gas constant for air is 280N-m/kg-K.
A getter screen consists of a cylinder of length l = 0.3m, diameter d=0.25m and its circular based plate. The getter screen is cooled with liquid nitrogen and coated completely with deposited titanium providing a constantly fresh surface. Sticking probability s=1 for N2 and mean thermal velocity = 470m/s. Find the pumping speed.
Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20 °C to 60 °C. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. a) Determine the Reynolds number b) What is the thermal coefficient on question number c) what is the heat absorbed by the water?
Hand written plz asap.... I'll rate plz fast plzzzzzzzzzzzzzz
Q3
Q2:A) Define the bulk temperature (Tn), and prove that : T₁, - 2 ur dr B) Ethylene glycol flows at 0.01 kg/s through a 3 mm diameter, thin walled_tube. The tube is coiled and submerged in a well-stirred water bath maintained at 25 °C. If the fluid enters the tube at 85 °C, what heat rate and tube length are required for the fluid to leave at 35 °C ? At 60 °C, μ = 0.00522 kg/m.s, k = 0.26 W/m.K, C, 2562 J/kg.K. -
A fluid is flowing from small diameter
A tube bank uses an aligned arrangement of 30 mm diameter tubes with ST = SL = 50 mm and a tube length of 1 m. There are 12 tube rows in the flow direction (NL = 12) and 6 tubes per row (NT = 6). Air with upstream conditions of T = 27 °C and V = 10 m/s is cross flow over the tubes, while a tube wall temperature of 90 °C is maintained by steam condensation inside the tube. Determine: a- The temperature of air leaving the tube bank (Exit temperature). b- The drop in the pressure across the bank.