ELEV. = 65m A ELEV. 32m L- 1500m 2 - 1400m D- 750mm Q= 1.2 m3/s D= 600mm ELEV. - ?? L= 1800m D= 450mm A three reservoir problem shown in the figure with their corresponding length and diameter. Assuming that each pipe has f= 0.02 and discharge at pipe 1 is 1.2 ma/s, determine the elevation of the surface of reservoir C No answer among the choices B 31.23 m 21.14 m 28.82 m 25.73 m F 18.96 m

ELEV. = 65m A ELEV. 32m L- 1500m 2 - 1400m D- 750mm Q= 1.2 m3/s D= 600mm ELEV. - ?? L= 1800m D= 450mm A three reservoir problem shown in the figure with their corresponding length and diameter. Assuming that each pipe has f= 0.02 and discharge at pipe 1 is 1.2 ma/s, determine the elevation of the surface of reservoir C No answer among the choices B 31.23 m 21.14 m 28.82 m 25.73 m F 18.96 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the piping system shown below, determine the flow distribution and the piezometric heads at the junction (j) using the Newton-Raphson Method of solution, power 20 Kw D = 0.2 m, D,= 0.15 m, D,= 0.15 m f= 0.021, f,= 0.018, f, = 0.023 L1=100 L2=145 L3=350 30 m В 2 15 m 10 m A Pump 1 j
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. Include minor losses. (DO NOT ROUND OFF)
Draw hp, hes and h, for the system shown in figure (A). Flow V Soil T K=1.5 cm/sec 2 Soil Il K=0.5 cm/sec Figure (A) DIL 1.0 m 1.5 m 1.0 m 1.0 m 1
Two reservoirs, A and B, are 7.5 km away from each other and connected by a 900 mm steel pipe ( f = 0.02). If reservoir A is 10 m higher than reservoir B, the pressure at B is 90 kPa greater that the pressure at reservoir A, what is the amount and direction of flow of water in the pipe. Use f = 0.02.
The following figure shows three reservoirs connected by pipes. Find the discharge in each pipe and the piezometric head H at the junction. 12 B 10 = 2000 m. L,= 2300 m. L= 2500 m 1 2 D,=1 m. D,=0.6 m. D,=12 m S-0013. -0.02. 1,-0023
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
For the pipe networks shown, the flow of water from reservoir A to the junction is 0.035 cu.m.per second. a) Determine Q2, Q3 b) Determine the head loss from A to B
o T ☺ ť Water is flowing in a compound open channel as shown in Figure. Given the channel bed slope as 0.0016 and Manning's n = 0.03, nz = 0.025 and ns = 0.03. calculate the flow rate using equivalent Manning's n method. Determine the equivalent n: i. ii. Determine the flow rate. 0.8 m 1.8 m 1.4 m 1.2 0.6 m مرّ للأعلى لاستعراض الفلاتر إضافة شرح. .. mum <
A pipe has a length of 213 m., and a diameter of 0.46 m. The coefficient of rouaness is C = 171, and the headloss is 17 m. Determine the discharge (L/s) inside the pipe.
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0.15 m3/s and 0.25 m/s respectively. If the coefficient of friction for the three pipes is 0.008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. hA h8 L2, D2 L1, D1 L1 = 1000 m L2 = 1500 m L3 = 2000 m D1= 200 mm D2 = 250 mm = 400 mm L3, D; hc %3D D3 = Figure 1: A three reservoirsystem
Determine the flow (m³/s) in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 L/s.
Three reservoir, named A,B, and C are connected by Pipe 1, Pipe 2, and Pipe 3 respectively joining at a common junction. Determine the into or out of the reservoir A in the pipe system, given the following data. Use n=0.011 for all pipes. Reservoir A at El. 30 m, B at El. 24 m, and C at El. 15 m Pipe 1: 30 cm dia. 1200 m long Pipe 2: 20 cm dia. 900 m long Pipe 3: 16 cm dia. 1500 m long