ELEV. = 130m L = 1000m D = 200mm f= 0.023 2 L= 1500m D = 250mm f = 0.02 Q = 0.14 m3/s L= 300m ELEV. = 40m D = 300mm f = 0.018 ELEV. =|10m D 3 A P Determine the power (in horsepower) delivered by the pump to the water system shown above, (A) 104.86 HP B 26.90 HP C No answer among the choices D) 60.86 HP E 97.64 HP F 148.32 HP B.

ELEV. = 130m L = 1000m D = 200mm f= 0.023 2 L= 1500m D = 250mm f = 0.02 Q = 0.14 m3/s L= 300m ELEV. = 40m D = 300mm f = 0.018 ELEV. =|10m D 3 A P Determine the power (in horsepower) delivered by the pump to the water system shown above, (A) 104.86 HP B 26.90 HP C No answer among the choices D) 60.86 HP E 97.64 HP F 148.32 HP B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

dynamics question m=20
HYDRAULICS
14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is 0.200 m³/s. The head loss due to major and minor friction losses is given by the equation, h₁ = 12.0 2g V 25 m Pump Determine the pump head. Also determine the shaft work done by the pump.
z=174 m A B z=152 m z=91 m T = and Op ≈pg əx (Pump) C F A pump is used to deliver water from a reservoir to a large tank for a flowrate of 1310 L/s at 20 °C. The connecting pipe connects the reservoir at B with a square-edged entrance. From B to C, the pipe is 760 m long and has three gate valves, four 45⁰ elbows, and two 90° elbows. Gage pressure at C is 197 kPa. From F to G, the pipe is 760 m long and contains two gate valves (Kg.-0.136), four 90° elbows (K90-0.51) and connects the tank with an exit (Kext=1). All pipe is 508 mm in diameter (D) and made by cast iron ( = 0.26 mm). 1) Calculate the average velocity of water in the pipe. 2) Calculate the gage pressure at F. z=104 m 3) If the pump's efficiency is 80%, calculate the power input to the pump. 4) If the shear stress can be calculated using the equation D Op hL major 4 0x L Calculate the average wall shear stress in section F-G. G H
Read the question carefully and give me right solution according to the question
Plz write neat
The pump in the figure B. draws water from a reservoir and discharges through 2 V2 inches hose, which terminates in a nozzle having a jet diameter of inch. The head losses are: I to 2. 5.75 ft: 2 to 3. negligible: 3 to 4. 30.61 ft. 4 to 5. 11.6 ft. Compute the required horsepower output of the pump and make a table of the heads at the five points. Q is (a) 261 gpm. (b) 361 gpm.
3) A centrifugal pump delivers water between two reservoirs with a 300 ft. elevation difference (Az). The 12-in diameter suction pipe (f1= 0.020) is 100 ft. long (L1) and the 10-in diameter discharge pipe (f2= 0.026) is 5000 ft. long (L2). The pump has a performance curve defined by the equation: h, = 375 - Q² where h, is the pump head in feet and Q is the discharge in ft/s. a) Calculate the discharge, Q. b) Calculate the NPSHA. Assume standard atmospheric conditions, 60°F water, and a pump elevation 8 ft. above the lower reservoir Az D, L2 2 D, Ly. ft LOM
Fluid 5
Determine the flow rate that circulates through each of the pipes in the system shown.
ELEV. = 130m B L = 1000m D = 200mm f = 0.023 L= 1500m L = 300m D = 250mm ELEV.= 40m D = 300mm f = 0.02 f = 0.018 Q = 0.14 m3/s ELEV. = 10m 3 A Determine the power (in horsepower) delivered by the pump to the water system shown above,
q7