give the functions of each part of a power tool responsible for electromechanical energy conversion electric motorarmatureMECHANICALENERGYfield windingcommutatorgearboxcooling fanbrushesbearingbrushholderon/off power switchELECTRICALENERGYstrain relief

Strain Relief:- For Protecting the wires and cable and to protect the device from stress we use…

Answered: electric motor armature field winding…

Engineering

Electrical Engineering

electric motor armature field winding MECHANICAL ENERGY commutator gearbox cooling fan brushes bearing

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.3MCQ: The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of...

See similar textbooks

Related questions

Q: € C.B. 1.1 CT, A Primary Y -moon Secondary A oooo 0000 0000 Restarting coil CT₂ Y for for Operating…

Q: Q23. Using the below circuit draw the following waveforms over the period of 4 m if the firi angle…

A: Given thyristor firing angle π which is 180° since thyristor works for postive half cycle with gate…

Q: A4 The field of a DC shunt generator is excited by al separate DC supply b) separate AC supply c)…

A: The field of DC shunt generator is excited by the generator itself. The equivalent circuit is as…

Q: Electrical Machines 2 What are the different parts of electromechanical energy conversion…

A: Electromechanical energy conversion topic forms the basis of electrical machines and is the sole of…

Q: (100 V DC serial motor has a starting current value of 50 A. Total armature resistance (Ra) value is…

A: The above question is based on DC series motor.

Q: The definition of Current in machine

A: An electrical machine works on the principle of electro-mechanical energy conversion. Any electrical…

Q: Write the power losses occured at a transformers only as titles by making a suitable classification.…

A: Definition:The transformer is a static device that converts the voltage from one level to another…

Q: Q12. In center-tapped rectifier, there are more stresses on the diodes compared to half wave single…

A: As per BARTLEBY GUIDELINES, I answered three questions (Q-12, Q-13, Q-14) and repost other…

Q: 4. Apply the technique of single node pair analysis to the upper right node and find ix (b) Now work…

Q: 2. An electrical power transmission system has various equipment and parameters. As shown in the…

A: The given circuit is shown below.

Q: kW and the rest of the losses for this machine (mechanical friction and ventilation losses) are 1,5…

Q: 1. How does speaker convert electrical energy to sound energy? 2. How does microphone convert…

A: Solve the first question, unless the student has asked for a specific question to be solved, subject…

Q: 1) (17 points) The input voltage and current of a single-phase power transformer are as indicated in…

Q: shunt motor has a starting line current value of of Ist= A, drawn from the voltage source. Total…

Q: Q22. Class A chopper is supplying a DC motor with FWD, motor inductance= 6 H & resistance- 12 SN,…

A: a) The maximum value of the load current is equal to : Imax.=VSR1-e-tONτ1+eTτ-ERVs=220 v ,E=5V,…

Q: (A Long shunt compounded DC motor has a nominal voltage of VT-100V. Its armature circuit total…

Q: riefly explain environmental issues in regard to thermal power plants

A: A thermal power station is a power plant with a steam-driven primary mover. Water is heated, then…

Q: ( Write the types and shortly explain the magnetic losses for electrical machines. )

A: In this question we discuss about type of magnetic losses for electrical machines

Q: (b) A three-phase A-connected synchronous generator is rated at 120 MVA, 10.5 kV, 0.85 PF leading…

Q: Describe electromechanical energy conversion in 300 words

A: to describe electromechanical energy conversion in 300 words

Q: Solar collectors are devices used for converting solar radiation into O a. thermal energy O b.…

A: Solar collector are collect the solar energy( heat ) convert it into thermal energy

Q: 1. Find the power absorbed by each of the six circuit elements + vi v2 +. V3 - 50 250 200 40V V= {…

A: Find the power absorbed by each of six elements given in the circuit ?

Q: Which of the following is NOT a variable in voltametric methods? A. How the current is applied B.…

A: In this question we need to choose a option which is NOT a variable in voltametric methods.

Q: What are the components of Electro mechanical Energy meters? and what are their functions?

A: Electro mechanical energy meter - This Energy Meters are the combination of Mechanical and…

Q: (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R=30 Ohm resistor…

A: Given data, RMS voltage Vr=240 V Frequency f = 60 Hz Load resistance, R=30 Ω Load current Io=2.5 A

Q: Explain the importance of electrical properties to agricultural processing

A: IMPORTANCE OF ELECTRICAL PROPERTIES TO AGRICULTURE PROCESSING: There are two principle electrical…

Q: 1. Single-phase transformer has a rated size of 15 kVA 2400/240 V 50 Hz and affects the transformer…

A: The data regarding short circuit and open circuit test of a transformer is shown below.The induced…

Q: Is it possible to detect maximum or peak AC voltage with an analog voltmeter?

A: Unless it’s a true-RMS meter, most multimeters work by rectifying the voltage and then measuring the…

Q: block diagram of the electromechanical energy conversion of a power tool

Q: (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R= 30 Ohm…

Q: 2. A DSB-SC AM signal is modulated by the signal m (t) = 2cos2000nt + cos6000nt. The modulated…

Q: Name and Discuss the process of how the heat energy is released from the Nuclear reactor? Discuss…

A: The process of heat energy release from the Nuclear reactor is known as Nuclear fission. Basically,…

Q: explain the principles of SMAW welding. b) explain the output slope of power source for SMAW c)…

A: Introduction: Welding is a fabrication method that involves fusing two or more pieces together using…

Question

give the functions of each part of a power tool responsible for electromechanical energy conversion

electric motor
armature
MECHANICAL
ENERGY
field winding
commutator
gearbox
cooling fan
brushes
bearing
brush
holder
on/off power switch
ELECTRICAL
ENERGY
strain relief

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

9.09 The flux density distribution in the air-gap of a certain generator is such that it contains a fundamental, a third harmonic, and a fifth harmonic. The flux per pole due to the fundamental distribution is 9 x 10-3 weber, that due to the third harmonic distribution is 0.9 x 10-3 weber, that due to the fifth harmonic distribution is 0.4 x 103 weber. There are four armature slots per phase per pole, the connection are made for three-phase wye. and the coil pitch is 12/15. The frequency is 60 cycles and the generator has 4 poles. (a) Calculate the emf/turn. (b) If there are six turns/coil and two coil sides/slot, calculate the emf per phase. (c) Calculate the emf between line terminals. Ans. 2.32V; 212V; 364V
For 4 pole d.c machine armature winding with a double layer progressive simplex wave winding with 23 number of slots answer the following: a How many coils are present? b What is the coil span in terms of number of slots? c What is commutator pitch in terms of commutator segments? d How many coils are there between two consecutive commutator segments? e How many parallel paths are present?
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
Question: In Dc chopper, the input voltage waveform is and the output voltage waveform is Option 1: Discontinuous,Continuous Option 2: Continuous, Discontinuous Option 3: Discontinuous,Discontinuous Option 4: Continuous,Continuous
How does the alternator end voltage change in resistive, inductive, capacitive loads? Please explain.
A commutator segment has 556 segments. Indicate whether or not the winding is possible; triplex wave for 6 poles.
For dc machines, the series field windings have many turns of fine wire true False
In the field circuit model of a DC machine, a variable _____ is usually inserted in series with the field winding to vary/control the _____ that flows through that circuit. A resistor, voltage B resistor, current C inductor, current D inductor, voltage
What is the Shunt de generator and Draw equivalent circuit?
In 2-pole machines: the wave winding have greater generated voltage than *.the lap winding armatures True False *.For high rotating speed machines the number of poles must be Little True False The reactance voltage is added in the coil undergoing commutation to * reduce the spark True False
The emf induced in the dc generator armature winding is * O AC and DC O DC O None of the above O AC
Draw the per-phase equivalent circuit of a three-phase squirrel-cage induction machine. List all of the elements in the equivalent circuit and briefly state their function