i need the answer quickly Each of the systems shown is initially at rest. Neglect axle friction and the mass of each pulley.100 B2100 1200200 lb2200 h(2)(3)Determine the time requited for block A to reach a velocity of 36 fus.The time reguired for block A in system (1) to reach the given velocity isThe time required for block Ain system (2) to reach the given velocity isThe time required for block Ain systemto reach the given velocity is

(1) The acceleration of the system can be determined as,

Answered: Each of the systems shown is initially…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve show all steps and solution. Energy systems engineering
Help me please
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
hints: The ﬂask will be filled with water (at a constant rate of 500 gallons per minute). It will take me exactly 10 minutes to escape from the chains. The diameter of the tank at 1 foot intervals. I am 5 feet 9 inches tall, and I'm pretty skinny so that you can ignore both my volume and the volume of the stool in your analysis. A gallon is equal to 0.13368 cubic feet. You can think of the volume and the height of the water as functions of time. You can easily find an expression for V (t), and then use your expression for volume in terms of height to solve for h(t). after 10 minutes amount of water in the tank=66.84 ft3 t=69.3 minutes h(t)=e66.84t/100? -1 h(10)=e66.84(10)/100? -1=7.39 ft Height of stool=1.64 ft Height of water in the tank=7.39 ft Questions: show work How fast is the water rising? I would like to know how long I will have to hold my breath during the last part of the stunt.
continue others
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached
SHOW YOUR SOLUTIONS PLS, THANKS show me how you did it so I can understand, thank you. Pls answer both, this is my last tutor question, pls. thank you. (Porosity). A dry rock weighs 240 grams and has a bulk density of 2.4 grams per cubic centimeter. When saturated with pure water at room temperature (T=25°C), it weighs 250 grams. At room temperature, the specific volume of water is 1.00295 x10-3m3/kg. Calculate the porosity of the sample. (Permeability). A cylindrical core sample of 1 cm length and 1 cm2cross-section has upstream and downstream pressures of 2 atm and 1 atm, respectively, during steady state flow of water at 0.997 g/s at room temperature. Calculate the permeability of the core. Note: Water @ 25°C, viscosity = 1 cp, density of water = 0.997 g/cm3.
Topics: Statics of Rigid Bodies, Equilibrium of Rigid Bodies, Equilibrium in Two Dimensions, etc. I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” THANK YOU FOR YOUR HELP. PS: If you have answered this already, don’t answer it again; give chance to other experts to answer it. I want to verify if all of you will arrive in the same final answer; thats why I ask it multiple times. If you answer it again, i'll dislike all your entries/answers.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Each of the systems shown is initially at rest Neglect axle friction and the mass of each pulley.