E.3. A machine having a total weight of 20000 kN has an unbalance such that itsubjected to a force of magnitude 5000 kN at a frequency of 600 rpm. What should be the spring consiarfor the supporting springs if the maximum force transmitted into the foundation due to the machine isto be 500 kN ? Assume that the damping can be neglected.

Answered: Image /qna-images/answer/5c87ff37-6489-4b3c-b6a7-5752d965fbce.jpg

E. 3. A machine having a total weight of 20000 kN has an unbalance such that it subjected to a force of magnitude 5000 kN at a frequency of 600 rpm. What should be the spring consta for the supporting springs if the maximum force transmitted into the foundation due to the machine is to be 500 kN ? Assume that the damping can be neglected.

E. 3. A machine having a total weight of 20000 kN has an unbalance such that it subjected to a force of magnitude 5000 kN at a frequency of 600 rpm. What should be the spring consta for the supporting springs if the maximum force transmitted into the foundation due to the machine is to be 500 kN ? Assume that the damping can be neglected.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(c) A vertical tie fixed rigidly at the top, consists of a steel rod 2.5 m long and 20 mm diameter encased throughout in a brass tube 20 mm internal diameter and 30 mm external diameter. The rod and casing are fixed together at both ends. The compound rod is suddenly loaded in tension by a weight of 10 kN falling through 3 mm before being arrested by the tie. Calculate the maximum stress in steel and brass. Take Es = 200 GPa and Eg = 100 GPa.
4. (a) A cantilever AB of length Im carries a uniformly distributed load, wN/m from the fixed end A to the free end B. If the cantilever consists of a horizontal plate of thickness 10mm and with 120mm as shown in the figure below, calculate the total permissible distributed load, w if the maximum bending stress is not exceeding 100 MN/m. Ignore the weight of the Plate. w N/m L. Im 120mm
SECTION: 500mm 20 KN I5 KNIM 1000 mm 12 m Ps 800 KN e : 400 mm (ASSUME IS % LOS SES) A. Determine the stress at the bottom in the free end. (MPa) B. Determine the stress at the top in the fixed end. (MPa)
The rigid block has a weight of 400 kN and is to be supported by posts A and B, which are made of A-36 steel, and the post C, which is made of C83400 red brass. If all the posts have the same original length before they are loaded, determine the average normal stress developed in each post when post C is heated so that its temperature is increased by 10°C. Each post has a cross-sectional area of 5000 mm². A HH B
A 2000-kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-sectional area 500 mm, as shown. Determine the location x of the largest additional force P which can be applied to the bar. The stresses in the cables AC and BD are limited to 80 MPa and 70 MPa, respectively. 18m 18m 2 in
Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt circle 320 mm in dia- meter and six 15-mm diameter bolts on a concentric bolt circle 240 mm in diameter. Determine the unit stress in each bolt due to a torque of 25 kN.m.
H.wl A solid shaft has to transmit 120 kW of power at 160 rpm. If the shear stress is not to exceed 60 MPa and the twist in a length of 3 m must not exceed 1°. Find the suitable diameter of the shaft. Take G = 80 GPa.
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 1. A 200mm 250mm 3. 30 N-m 300mm 20 N-m 80 N m O 2.34MPA O 7.49MPA O 4.68MP O 3.74MPA
A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Assume TA - 536 N-m, Tg - 1340.0N-m, Tc - 1072 N-m, and To - 268.0 N-m. Determine the magnitude of the maximum shear stress in the shaft. TB Tc Tp (3) (2) B D Answer: Tmax" MPа
1. A cylindrical steel container 8m high and 3m in diameter is reinforced with two hoops a meter from each end. If the contained liquid is gasoline (0.87), determine the: a) normal force acting on the wall of the tank b) with an allowable stress of 0.12 GPa, compute the thickness of the steel required. Dear expert, I have answer to the total hydrostatic force which is F=819.3312. I also have answer to the tension of hoop at the bottom (T=295.869) and the top (T=113.769). But no one has helped me find the normal force and thickness of steel required. Please help me, thank you.
A rigid bar, hinged at one end, is supported by two identical springs as shown. Each spring consists of 20 turns of 10-mm wire having a mean diameter of 150 mm. Compute maximum shearing stress in the springs. Neglect the mass of the rigid bar.
A transmission tower is loaded as shown in the figure JCZ-1. Assume roller support at A and hinge support at B. Determine the stresses at member CE and DF.