e unsymmetrical built-up section of the given dimensions supports the ven load shown. Determine the maximum fv or the beam shear eveloped in MPa. a 10 KN а 60 7 KN b 25 6 KN/m 12 KN/m c 180 d 45 1m 3m 2m е 30 f 125 ultiple Choices o 3.84 € (WRONG ANSWER) o 1.84 o 2.84

Q: uppose you are asked to conduct an experiment to study the impact of three factors(temperature: high…

A: Design of experiments (DOE) is nothing but a technique that is used to optimize the product cost and…

Q: In the drawing operation, technological property weldability is an important parameter. Select one:…

A: Drawing: It is a process in which uses tensile forces is used to stretch metal.

Q: Number of manufacturing processes are listed below. Each manufacturing process has some…

A: Commonly used materials Metal is the most common material used for various types of the purposes…

Q: Define design rationale and its benefits?

A: Design rationale is an explicit document stating the various reasons behind decisions made while…

Q: Sclect an appropriate manufacturing process where dimension accuracy and precisions are critical.…

A: Extreme tolerances are required to ensure proper performance and reliability. In automotive…

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: In the 3% error, why is the design acceptable?

A: Given: There are 3% error in the design. And by this error the developed power reduced from 0.556 MW…

Q: What are the three metrics for assessing the success of a design.

A:

Q: need answer within 20 minutes please please with my best wishes

A: Superfinishing is different from honing in a way that:- In honing the small removable of material…

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: Do you think it is an advantage if you’re knowledgeable in the use of the various carpentry tools…

A: Yes, It is knowledgeable. A carpenter is nearly crucial as distant as the development industry…

Q: Why should the thermal stresses be considered in design?

A: The stresses generated due to rapid heating or cooling of the structure are known as thermal…

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is second.

Q: What do you mean by fixed cost and variable cost? Provide at least three examples of each item.

A: Fixed costs are expenses that do not vary with the level of production or sales. These costs stay…

Q: Drilling and Completion Engineering II An exploration well is to be drilled to a total depth of…

A:

Q: How to use layers and what you can do with layers on your CAD drawing

A: Given: Layers on CAD drawing To write: How to use layers and what you can do with layers on your CAD…

Q: How is it possible to solve statically indeterminate problems?

A:

Q: In the context of our teaching, which one of the below statements is mostly correct about in…

A: Component design, sometimes known as atomic design (though we prefer "Component design" at…

Q: 8.[Short Answer] As shown in this figure, what's the function of inclined plate colored yellow ?

A: Ans : The structure is showing like truss system where five members or links are attached to each…

Q: Describe the operational characteristics of a Direct Acting Relief Valve B) A single paragraph…

A: The characteristics of a direct-acting relief valve can be used in a simple circuit to control the…

Q: With your expertise as a quality reliability engineer, how would you achieve a product life cycle in…

A: GIVEN: With your expertise as a quality reliability engineer, how would you achievea product life…

Q: List some five factors that influence machine design

A: Machine design: The machine design is the iterative decision-making activity to produce a plan or…

Q: Trace a rough front and top view of a given isometric drawing. Also write the maximum possible steps…

A: The isometric view is given by

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: Expound why we use CAD and its advantage to manual drawing.

A: Given CAD To find Advantage of CAD use Advantage of CAD over manual drawing

Q: Using scientific methods, how would you know the right temperature and heat needed to bake to right…

A: Following steps can be used - With the help of protein denaturation temperature, we can know the…

Q: requirements form into different Shape, why do we need it in the design of machine elements well…

A: Machine elements are to be designed within elastic deformation regime because

Q: OM A customer has recently tightened the specs for a part your company supplies. The specs are now…

A: Explanation: 1.Firstly identify the clause in revised specification which is very critical.  2.So if…

Q: What kind of information does a detail view on a drawing provide

A: A detailed drawing can be drawing of an object, assembly of multiple parts, or an entire system of…

Q: Hello. Would it be possible to include detailed explanations in every step? Thank you.

A: Given: Two springs are opposite to each other and by the energy stored in spring A is transferred by…

Q: What are the significance of tolerance and allowance in production process? Diagram?

A: Tolerance and Allowance

Q: Estimate the manufacturing cost for a simple machined component: a. Compare the costs for…

A: To Compare:a) The costs for manufacturing volumes of  and  pieces with an intermediate tolerance and…

Q: An assembly drawing with numbering of all parts and the dimensions needed only for assembling,…

A: AS per the Question Demand the Drawing of the Power Screw Device. Power Screw Device is the…

Q: Q3: How does superfinishing differ from honing?

A: This question is based on the concept of honing and super finishing from manufacturing engineering.

Q: Sketch 1pt, 2pt, 3pt perspective of a chair. Kindly put orthogonal lines. Thank you

A: Engineering Drawing Find One-point, two-point, and three-point perspective drawings of a chair.

Q: b) Use your own sketches to show how surface finish is measured and define 2 important parameters…

A: B) Surface finish is a characteristic of any machined surface. It is sometimes called surface…

Q: a) Define what is meant by "surface finish" and describe 2 ways in which it should be specified on…

A: a) The three properties of lay, surface roughness, and waviness describe the nature of a surface…

Q: There are two types of scales in aerial photographs, mention and explain them briefly

A: There are two types of scale in aerial photographs: i) large scale photograph ii) small scale…

Q: Thank you, Could you help me with Problem 60 as well?

A: Given the force and its position.  Required: Moment of force about y axis.