e strength in compression o is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Given:- Allowable normal stress in BC = 165 MPa To determine- a) Is this a frame or a truss? b)…

Q: 3

A: Given:- factor of safety =1.6 force=100kips To find:- most economical option

Q: When solving the problems for Section 1.6, assume that the material behaves linearly elastically.…

A: Given data in question  Diameter  Elasticity modulus  Poissons ratio  To find out  Largest force P

Q: A solid brass E = 100 GPa axial member is loaded and supported as shown in the figure. Segments (1)…

A: Given data,  W1 = 35 kN W2 = 14 kN W3 = 28 kN E = 100 GPa L1 = 1.8m L2 = 1.2 m L3 = 1.6 m To find…

Q: GIVEN: Solid aluminum bar shown: 4 in. by 4 in. E = 10 x 10° psi oy = 36 ksi 4000 & 200016 4000 16 B…

A: A) Load in each section of bar PAB = 4000 lb ( T )  PBC = 4000 - 2000 = 2000 lb ( T ) PCD = 4000 -…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A: Given:- The magnitude of the shear force = V = 36 kips The dimensions of the cross-section are:- b =…

Q: A threaded round steel bar is subjected to a tota axial pull of 8000 lb. If the diameter of the…

A: Take diameter of threaded portion≈unthreaded portionso,Stress=PArea

Q: Problem 2-4. For the following section, constructed of steel, determine: a) Moment at first yield…

A:

Q: 4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at…

A: Given data: dB=1/4 in. dw=7/8 in. t=3/8 in.

Q: Draw the V&M diagrams and calculate the largest permissible value of P for the beam and loading…

A: Allowable normal stress in tension=-80MPa Allowable normal stress in Compression=-140MPa To find…

Q: The plates in the figure below are each 3 inches by 0.5 inches in cross section. If the hole in each…

A: Solution:- Given information: Cross section of plate =3×0.5 in Hole diameter, d=1316 in, and Load,…

Q: The maximum safe compressive stress in a hardened steel punch is limited to 0.8 GPa and the punch is…

A: The given data is: Maximum safe compressive stress=0.8 GPa=800 MPa The shearing stress of plate=300…

Q: THE PLATE SHOWN IN THE FIGURE IS FASTENED TO THE FIXED ΜΕMBER BY FIVE 10- MM- DIAΜΕ TER RIVETS.…

A:

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A: P=8kN

Q: determine the minimum force P required to punch the slot. Punch O 575 kN O 675 kN O 724 KN Slug…

A:

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A:

Q: What would be the temperature at which the bar will have a compressive stress of 3 MPa given that at…

A: Elongation due to temperature change δT=Lα(ΔT)ΔT=T2-T1=T2-(-20)=T2+20

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.